JLG GRADALL 544D-10 Скачать руководство пользователя | Manualshive

Страница: 63 / 142

background image

Section 5 - Attachments

5-1

31200172

SECTION 5 - ATTACHMENTS

5.1

APPROVED ATTACHMENTS

To determine if an attachment is approved for use on the specific telehandler you are
using, perform the following prior to installation.

Before S/N 0160037689

• The attachment model/option number on the attachment identification plate must

match the attachment number on a capacity chart located in the operator cab.

• The model on the capacity chart must match the model telehandler being used.

• The load center of the fork (if equipped) must match the load center as indicated

on the capacity chart.

• Hydraulically powered attachments must only be used on machines equipped

with auxiliary hydraulics.

• Hydraulically powered attachments that require auxiliary electrics must only be

used on machines equipped with auxiliary hydraulics and electrics.

S/N 0160037689 & After

• The attachment type, weight, dimensions and load center must be equal to or

less than the data shown on a capacity chart located in the operator cab.

• The model on the capacity chart must match the model telehandler being used.

• Hydraulically powered attachments must only be used on machines equipped

with auxiliary hydraulics.

• Hydraulically powered attachments that require auxiliary electrics must only be

used on machines equipped with auxiliary hydraulics and electrics.

If any of the above conditions are not met, do not use the attachment. The
telehandler may not be equipped with the proper capacity chart or the attachment
may not be approved for the model telehandler being used. Contact JLG or a local
distributor for further information.

«
...
61
62
63
64
65
...
»

Содержание GRADALL 544D-10















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRADALL 544D-10

Бренд: Terex Страницы: 301

Бренд: TLS Страницы: 30

Бренд: TLS Страницы: 30

Бренд: Peak Страницы: 37

Бренд: Peak Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды