SECTION 7 - JLG CONTROL SYSTEM
3121222
– JLG Lift –
7-1
SECTION 7. JLG CONTROL SYSTEM
7.1
ELECTRONIC CONTROL SYSTEM
To Connect the Hand Held Analyzer:
1.
Connect the four pin end of the cable supplied
with the analyzer, to the four position connector
on the PCB and connect the remaining end of the
cable to the analyzer.
NOTE:
The cable has a four pin connector at each end of the
cable; the cable cannot be connected backwards.
2.
Power up the Control System by turning the lower
key to the platform position and pulling both
emergency stop buttons on.
Using the Analyzer:
With the machine power on and the analyzer connected
properly, the analyzer will display the following:
HELP:
PRESS ENTER
At this point, using the
RIGHT
and
LEFT
arrow keys, you
can move between the top level menu items. To select a
displayed menu item, press
ENTER.
To cancel a selected
menu item, press
ESC
; then you will be able to scroll using
the right and left arrow keys to select a different menu
item.
The top level menus are as follows:
(Also see menu flow charts - Figure 7-1. and Figure 7-2.)
HELP
DIAGNOSTICS
ACCESS LEVEL
PERSONALITIES (See Table 7-3 on Page 7-11)
MACHINE SETUP (See Table 7-1 on Page 7-9)
ACTIVATE TESTS
CALIBRATION
If you press
ENTER
, at the HELP:PRESS ENTER display, and
a fault is present during power up, the analyzer display will
scroll the fault across the screen. If there was no fault
detected during power up, the display will read:
In platform mode
,
HELP: (001)
EVERYTHING OK,
In ground mode
,
HELP: (002)
GROUND MODE OK
If
ENTER
is pressed again, the display moves to the follow-
ing display:
LOGGED HELP
LOG: (211)
1: Power Cycle
(Or last recorded fault)
At this point, the analyzer will display the current fault, if
any are present. You may scroll through the fault logs to
view what the last fifteen faults were. Use the right and left
arrow keys to scroll through the fault logs. To return to the
beginning, press
ESC
two times.
MENU:
HELP:PRESS ENTER
l og: ( 211)
Содержание 1230ES
