JCM ivizion ld страница 88 Скачать руководство пользователя

Страница: 88 / 158

P/N 960-100929R_Rev. 7 {EDP #148849}

6 - 1 6

Section 6

iVIZION® SeriesNext-Generation Banknote Acceptor Unit

Calibration and Testing

Performance Test Tool Requirement using an

External DIP Switch Box

Figure 6-62 illustrates and list identifies the Tools

and equipment interconnects necessary to perform

the

iVIZION

Performance Tests using an External

Switch Box.

External DIP Switch Performance Test

Procedure Settings

Table 6-2 lists the DIP Switch settings for the

Performance Tests using the External Switch Box.

Performance Tests with External Switch

Procedures

Perform the following steps to test the Motor

Normal Forward and Reverse Rotation, the Stacker

Motor, the Cyclic Movement Test, the Status LED

Indication Test, the Banknote Transportation and

the ICB Function Setting Performance Tests.

1. Turn the iVIZION Power Switch

OFF

2. Remove the Transport Unit from the Frame.
3. Set the appropriate DIP Switch(es) to “

” for

the test desired using the 8-Position DIP Switch
(Table 6-6).

4. Place the Transport Unit back onto the Frame.
5. Connect the third the fourth Pin Connector of the

External Switch Box Cable to the corresponding
Connector Pins of the five (5) Pin Plug located at

the rear side of the iVIZION Transport Unit

6. Set the External Switch Box Switch to the posi-

tion away from the Status LED on the Box.

7. Turn the iVIZION Power Switch to

. The

iVIZION Status LEDs will indicate Stand-by
Mode when the Status LED on the iVIZION

Lights a steady

Blue

Color, and the Status LED

on the External Switch blinks at a

Red

Color rate.

8. Turn the External Switch Box Switch toward the

iVIZION status LED on the Box. The desired
Test selected by DIP Switch Positions will then

begin (Refer to Table 6-6 “Performance Test DIP

Switch Settings” on page 6-16 of this Section for
each test and its resulting Test indication).

9. Return the External Switch Box Switch to the

position away from the iVIZION Status LED on

the Box again, and the current Test being run will

end. If other Switch Box Tests are necessary,
restart from Step 1 at the beginning of this

procedure.

iVIZION Utility Tools

This portion provides information regarding each

iVIZION

Service Mode setting procedure.

The following two (2) Tool setting types exist when

using the iVIZION Utility Tools:

•

CIS Image Views

•

ICB Function Settings.

ICB/Image Setting Tool Requirements

Table 6-6

Performance Test DIP Switch Settings

*. NOTE: The Sensor ON/OFF Test and the DIP Switch ON/OFF Test

are ONLY available when using the PC procedure!

No. Test Item

Status LED

DIP Switch Setting (O = ON)

Stand-

Operat-

ing

Motor

Normal

Rotation

Blue

Lit

Yellow

Flashes

Motor

Reverse

Rotation

Stacker

Motor

Cyclic

Movement

Status LED

Indication

Red

Green

Blue

Banknote

Accept-

ance

Exting-

uished

(Out)

ICB Setting

(Reading

Ticket)

Figure 6-62

Calibration Tool Requirements

Figure 6-62

Calibration Tool Requirements

a) iVIZION Unit
b) Power Supply (12V DC - 24V DC)

c) External Switch Box

(User provided)

d) Interface Cable (3380-05-01 EDP#146780)

MOLEX 4-Pin

MOLEX 3-Pin

MOLEX 2-Pin

NOTE: Refer to Figure 6-1 and Figure 6-2

for the necessary Tools and Harness

Connections and USB Cable Type

Requirements respectively.

NOTE: The ICB Function Status is initially

Factory Set to “INHIBIT” as a standard

function. Therefore, the iVIZION Unit’s ICB

must be first initialized using the USB Tool

Suite Utility Options. Refer to the JCM ICB

Installation Guide for exact programming

descriptions and operational details.

Содержание ivizion ld































































































































































Результаты поиска

Содержание ivizion ld

Отзывы:

Похожие инструкции для ivizion ld

Бренды по названию

Популярные бренды

JCM ivizion ld, Эксплуатация и обслуживание

Результаты поиска

Содержание ivizion ld

Отзывы:

Похожие инструкции для ivizion ld

Бренды по названию

Популярные бренды