P/N 960-100929R_Rev. 7 {EDP #148849}
© 2017, JAPAN CASH MACHINE CO., LTD.
2 - 1 0
Section 2
iVIZION® Series Next-Generation Banknote Acceptor Unit
Installation
Preventive Maintenance
Retrieving Banknotes
To retrieve Cash Box deposited Banknotes perform
the following steps:
1. Release the Cash Box from the Frame and pull it
forward.
2. Unlock the Cash Box with a User supplied Key.
3. Open the Cash Box Door and retrieve deposited
Banknotes as illustrated in Figure 2-7.
Clearing a Banknote Jam
To retrieve a jammed Banknote jammed inside the
Banknote Acceptor Head proceed as follows:
1. Open the Acceptor Unit’s Upper Guide by press-
ing in on the two (2) Upper Guide Access Buttons
a
) located on each side of the Upper
Guide, and lift the Acceptor top up and open and
remove the jammed Banknote.
2. If the jammed Banknote is not found in the
Acceptor Unit, then
3. Open the Transport Unit’s Upper Guide by press-
ing in on the Upper Guide Access Lever (Figure
b
) located in the center of the Upper Guide,
and lift the Transport Section up and open and
remove the jam.
4. If the jammed Banknote is not found in the higher
Sections, pull the Cash Box out of the Frame
a
). Check at the rear side of the Frame
and remove the jammed Banknote located there if
b
).
5. A jammed Banknote may also be present on top
of the Cash Box; remove it if present at this
location (Figure 2-9
c
).
Cleaning Procedure
To clean the lenses, use a lint-free, Micro-Fiber
Cloth and a mild non-abrasive detergent such as
liquid dish soap mixed with water to wipe the dirt
from the Lenses. It is important to keep the
Banknote Path, Rollers, and Belts clean. Use a soft-
lint free, Micro-Fiber Cloth or a Cotton Swab to
wipe dirt and stains from the surfaces of the Optical
Sensors, Rollers and Belts. The Sensor Lenses are
transparent, and made of a polymer material; Han-
dle them with care. When the Unit is exposed to
liquid such as water, wipe and dry the wet areas
immediately. Repeat the cleaning process as needed
until the Transport Path is free of contaminants.
Sensor Cleaning Procedure
1. Turn
the
iVIZION
Unit Power OFF.
2. Clean the Sensors and lenses in the Acceptor
Unit, the Transport Unit and on the Cash Box
itself. If necessary, remove each Unit and/or open
their Upper Guides for cleaning. See Figure 2-12
and Table 2-12 to locate all cleaning locations.
Figure 2-7
Remove
Figure 2-7
Retrieving Banknote
Figure 2-8
a
) Acceptor Unit Upper Guide Access Lever
b
) Transport Unit Upper Guide Access Lever
Open
Open
b
a
Remove
Hidden
Figure 2-8
Open the Upper Guides
Figure 2-9
Retrieving Cash Box Banknote Jam
Figure 2-9
Retrieving Cash Box Banknote Jam
Pull Out
a
c
b
Caution: Do not allow any fluid to remain
on internal components, especially on
the Anti-String Mechanism and in the
Feed-in Sensor’s grooved areas.
Caution: Do not use Alcohol, thinner or
citrus based products for cleaning any
Banknote transport Sensors or surfaces.
The lenses can become clouded by
chemical evaporation residue that may
cause acceptance errors.
NOTE: When closing the Acceptor or
Transport Unit’s Upper Guides, ensure that
they click firmly into place when being
closed. Also, when reassembling the
iVIZION Unit, ensure that it re-seats correctly
into place when the reassembly is complete.