janitza UMG 96 RM-E Скачать руководство пользователя страница 125

Страница: 125 / 126

125

UMG 96RM-E

TCP/IP addressing quick guide

Manual TCP/IP settings
Switch to the programming mode:
• Press button 1 and 2 simultaneously for around

1 second to switch to the programming mode.
The symbols for the programming mode PRG
and the current transformer mode CT appear
on the display.

Adjust the TCP/IP address (Adr.)
• Press button 2 to select "Adr"
• Press button 1 to enable the first digit (byte 0)

of the address (digit is flashing). Press button 2 to set
the digit.

• Press button 1 to select the next digit (flashing) and set

the desired digit by pressing button 2.

• If byte is set to 0, the address can be set from 1 to 3

by pressing button 1. Then the display jumps back
to Byte 0 (

no digit is flashing).

Subnet mask (SUb)
• Press button 2 to select the subnet mask and set

it in a manner similar to adjusting the address
by pressing button 1 and 2.

Adjusting the gateway address (GAt)
• Use button 2 and 1 to set the gateway in a manner

similar to adjusting the address.

Exit programming mode
• Press button 1 and 2 simultaneously to exit the mode

or wait 60 seconds.

Description

Byte identification
(e.g. byte 0) of the address

Address data, byte 0

Fig. TCP/IP address, byte 1

A TCP / IP address consists of 4
bytes with the following structure:

xxx.xxx.xxx.xxx

Byte 1

Byte 0

Byte 2 Byte 3

Enable dynamic IP allocation (dyn)
Device/gateway address and subnet mask are assigned
by a DHCP server and enable automatic integration
of the device into the existing mains.
• When in programming mode, press button 2

repeatedly to display the tab labelled "dYn IP".

• Press button 1 to enable the parameter "on"

or "oFF" (parameter is flashing). Press button 2 to set
the desired status and press button 1 to confirm
the selection.

• Exit programming mode.

Содержание UMG 96 RM-E































































































































Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды

janitza UMG 96 RM-E, Руководство пользователя и технические характеристики

Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды