janitza UMG 96 RM-E Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 126

background image

64

UMG 96RM-E

Measured value rotation

All 10/12 periods the measured values are calculated
and the readings are displayed on a per second basis.
There are two ways to retrieve the measurement
readings:

• The automatically changing indication of the selected

measurement readings is referred to herein
as measured value rotation.

• Press button 1 and 2 to select measured value

indication from a pre-selected display profile.

Both methods are available simultaneously.
The measured value rotation is enabled when at least
one measured value indication change time is over
0 seconds.
Press a button to scroll the measured value indications
of selected display profile. If no button is pressed for
about 60 seconds, the device will switch to the measured
value rotation to display the programmed measured
value indications from the selected rotation profile
in succession.

Rotation time (Addr. 039)

Setting range : 0 .. 60 seconds
If 0 seconds are set, the measured value indications
selected will not be rotated.
The rotation time set applies to all display rotation
profiles.

Display rotation profile (Addr. 038)

Setting range: 0 .. 3
0 - Display rotation profile 1, pre-programmed.
1 - Display rotation profile 2, pre-programmed.
2 - Display rotation profile 3, pre-programmed.
3 - Display rotation profile, customizable.

Measured value indocations

Following a power resumption, the UMG 96RM-E
displays the first measurement value table in the current
display profile. To keep the selection to a manageable
size, only a fraction of the available measurement values
was preprogrammed in the factory for retrieval in the
measured value display. Select another display profile
to view other measured values on the UMG 96RM-E
display.

«
...
62
63
64
65
66
...
»

Содержание UMG 96 RM-E































































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 96 RM-E

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: Oldham Страницы: 22

SourceMeter 2400

Бренд: Keithley Страницы: 594

System SourceMeter 2601B

Бренд: Keithley Страницы: 864

Бренд: Labgear Страницы: 8

SourceMeter 2600B Series

Бренд: Keithley Страницы: 897

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: PASCO Страницы: 3

Бренд: PASCO Страницы: 2

Бренд: NanoPhotometer Страницы: 133

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

BUCKMASTERS 1500

Бренд: Sig Sauer Страницы: 2

Бренд: DODODUCK Страницы: 2

Бренд: Spasciani Страницы: 26

Бренд: Magnescale Страницы: 2

Бренд: Datakom Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды