janitza UMG 96 RM-E Скачать руководство пользователя страница 82

Страница: 82 / 126

UMG 96RM-E

Pulse value

The pulse value is used to indicate how much energy
(Wh or varh) should correspond to a pulse.
The pulse value is determined by the maximum
connected load and the maximum number of pulses per
hour.

If you check the pulse value with a positive sign,
the pulses will only be emitted when the measured value
has a positive sign.

If you check the pulse value with a negative sign,
the pulses will only be produced when the measured
value has a negative sign.

Since the reactive energy meter operates with
a backstop, pulses will only be generated
with inductive load applied.

Since the active energy meter operates with
a backstop, pulses will only be generated
when drawing electricity.

Pulse value =

max. connected load

max. number of pulses/h

[Pulse/Wh]

Содержание UMG 96 RM-E































































































































Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды

janitza UMG 96 RM-E, Руководство пользователя и технические характеристики

Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды