janitza UMG 96 RM-E Скачать руководство пользователя страница 39

Страница: 39 / 126

UMG 96RM-E

Ethernet interface

The Ethernet network settings should be specified
by the network administrator and set on UMG 96RM-E
accordingly.
If the network settings are not known, the UMG 96RM-
E may not be integrated into the network through
the patch cable.

Caution!
Connection of the UMG96RM-E to the
Ethernet may only be carried out after
discussion with the network administrator!

PC / Switch

Ethernet

Connection

Caution!
The UMG 96RM-E is factory-programmed
for the dynamic allocation of the IP settings
(

DHCP mode).

Settings can be changed as described
in TCP/IP Configuration or, for example,
via an appropriate Ethernet connection
by means of GridVis software.

Содержание UMG 96 RM-E































































































































Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды

janitza UMG 96 RM-E, Руководство пользователя и технические характеристики

Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды