janitza UMG 96 RM-E Скачать руководство пользователя страница 15

Страница: 15 / 126

UMG 96RM-E

Installation

Power supply

The 96RM-E needs a supply voltage to operate.
The supply voltage is connected on the rear of the device
via terminal blocks.

Before connecting the supply voltage, ensure that
the voltage and frequency correspond to the details
on the ratings plate!

Fig. connection example of the supply voltage
to a UMG 96RM

Circuit breaker

Fuse

• The supply voltage must be connected

through a fuse according to the technical
data.

• If installed in a building, a disconnector

or circuit-breaker must be provided for
the supply voltage.

• The disconnector must be installed

near the device and easily accessible
to the user.

• The switch must be marked as the circuit

breaker for this device.

• Voltages which are over the permitted

voltage range can destroy the device.

Содержание UMG 96 RM-E































































































































Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды

janitza UMG 96 RM-E, Руководство пользователя и технические характеристики

Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды