janitza UMG 96 RM-E Скачать руководство пользователя страница 14

Страница: 14 / 126

UMG 96RM-E

Mounting

The UMG 96RM-E is fixed using the mounting clips
found on the side of the switch panel. Before inserting
the device, they should be moved out of the way
in a horizontal lever using a screwdriver, for example.

Fig. side view
UMG 96RM-E with
mounting clips.
Loosening the clips
is done using
a screwdriver
and a horizontal lever
effect.

Mounting plate

Fixing screw

Screwdriver

Mounting
clips

Contacting of the
fixing screws to the
mounting plate:
Tighten with maximum
two further turns for
the installation

The fastening is then done when the device is pushed
in an the clamps lock in place when the screws are
tightened.

• Please tight the fixing screws until they contact the

mounting plate easily.

• Tighten with two further turns, the clamping screws

(are the screws tightened too much, the mounting
bracket will be destroyed)

Содержание UMG 96 RM-E































































































































Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды

janitza UMG 96 RM-E, Руководство пользователя и технические характеристики

Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды