janitza UMG 96 RM-E Скачать руководство пользователя страница 40

Страница: 40 / 126

UMG 96RM-E

Digital in-/outputs

The UMG 96RM-E has 2 digital outputs and 3 optional
digital inputs or outputs, which are divided into two
groups (see figure). This means that only

entire group 2

(connection 28 to 31) operate either as input or output;
a different allocation within the group is not possible!

Digital outputs, Group 1
• The status indicator appears on the display at K1 or

• The status indicator on the display is not dependent

on an inversion being activated (NC / NO)

Digital outputs, Group 2
• The status of the inputs and outputs in Group 2 is

indicated by the associated LED (cf. chapter LED
status bar).

Digital
output 3

e.g.
Comparator group

Inverter

Source

Digital
output 1

e.g.
Comparator group

K1/K2 display
status indicator

Inverter

Source

The digital outputs of group 2 are

not AC

compatible.

Содержание UMG 96 RM-E































































































































Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды

janitza UMG 96 RM-E, Руководство пользователя и технические характеристики

Результаты поиска

Содержание UMG 96 RM-E

Отзывы:

Похожие инструкции для UMG 96 RM-E

Бренды по названию

Популярные бренды