Jabiru 2200 Скачать руководство пользователя страница 179

Страница: 179 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 179 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

9.10 Top End Overhaul Booklet

9.10.1 Engine Details

Engine Serial #:

Date:

9.10.2 Top End Subassembly A Build Sheet

– Conrods

Table 27

– Top End Build Sheet A

No.

Details

Para

Initials

Checked By

Date

Clean Conrods

5.9

Inspect and measure Conrods (includes bearing
crush, bearing clearance)

5.9,

7.1

Fit the Conrods to the Crankshaft; Use Loctite
620 on the bolts and torque per Table 9

7.1

Record measurements & clearances in build
record

sheet

Table

26.

Ensure

all

measurements and clearances are within the
appropriate limits given in Table 10 and Table 12

Stage A - Stage Inspection of Assembly

I hereby certify that the above subassembly has been assembled in accordance with the applicable Jabiru
Pty Ltd Instructions and Maintenance procedures.

Signed:

Date:

for Jabiru Aircraft Pty Ltd

MPI Release Note No.

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Jabiru 2200, Руководство по капитальному ремонту, Страница: 179 / 201

Результаты поиска

Содержание 2200

Отзывы: