Jabiru 2200 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 201

Jabiru 2200 Скачать руководство пользователя страница 119

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

6 7

Dated : 28/10/2014

Issued By: AS

Page: 119 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

has a front and a back

– care must be taken to orient it correctly to the flywheel body, aligning the

datum holes in the starfish and flywheel body.

Figure 145

– Flywheel Assembly

7.5.4 Starter Motor



Assemble motor and starter housing, and include the earth wire, (refer to JSL 005-1 service bulletin for

details  if  the  earth  wire  connection  was  not  connected  to  the  long  through  bolt  on  the  starter  motor).
Assemble  bolts  with  a  small  amount  of  Loctite  243  on  the  threads  of  the  long  AN3  bolts  and  tighten,
check that the armature is able to rotate freely after tightening bolts.



Apply grease to the clutch gear and assemble into the starter housing, then fit the clutch housing.



The assembly is now ready to be fitted to the engine rear plate with the 3 socket head screws and

Belleville washers, torque per Table 9.

Locating roll pin

Dowel hole

Flywheel tacho tag

Timing mark

Datum hole

«
...
117
118
119
120
121
...
»

Содержание 2200










































































































































































































Отзывы:

Нет отзывов