ITT Goulds Pumps API 3171 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 64

background image

Maintenance

Model API 3171 Installation, Operation, and Maintenance Manual

40

Grease recommendations based on temperature

Most pumps use Sunoco 2EP grease. High temperature units that can pump fluids with a temperature
greater than 177°C | 350°F use Mobil SCH32.
This table shows which brand of grease to use when lubricating the pump.

Brand

When temperature of pumped
fluid is less than 177°C | 350°F
NLGI consistency 2

When temperature of pumped
fluid is greater than177°C |
350°F NLGI consistency 3

Mobil

Mobilux EP2

SCH32

Exxon

Unirex N2

Unirex N3

Sunoco

Mutipurpose 2EP

N/A

SKF

LGMT 2

LGMT 3

Regrease the thrust bearing

NOTICE:
Risk of equipment damage. Ensure that the grease container, the greasing device, and the
fittings are clean. Failure to do so can result in impurities entering the bearing housing while
regreasing the bearings.

1. Wipe dirt from the grease fittings.
2. Remove the two grease-relief plugs from the bottom of the frame.
3. Fill both of the grease cavities through the fittings with a recommended grease until the

fresh grease comes out of the relief holes.

4. Make sure that the frame seals are seated in the bearing housing.

If they are not, press them in place with the drains located at the bottom.

5. Reinstall the grease-relief plugs.
6. Wipe off any excess grease.
7. Recheck the alignment.
The bearing temperature usually rises after you regrease due to an excess supply of grease.
Temperatures return to normal in about two to four operating hours as the pump runs and
purges the excess grease from the bearings.

Steady bearings

Check the ID of the casing collar (155) and steady bearing (197) per the dimensions in the
Bearing fits and tolerances table. If the ID is greater than what is allowed, remove the snap ring
(369) and use a suitable hydraulic press in order to remove these items for replacement. If
sealed bearings are provided, then you must also remove the lip seals (333H).
The bearing ID is slightly larger before you press it into the housing in order to allow for ID
shrinkage after you press it in place.

Shaft-seal maintenance

Mechanical-seal maintenance

WARNING:

The mechanical seal used in an Ex-classified environment must be properly certified.

CAUTION:
Running a mechanical seal dry, even for a few seconds, can cause seal failure and physical
injury. Never operate the pump without liquid supplied to the mechanical seal.

Cartridge-type mechanical seals

Cartridge-type mechanical seals are commonly used. Cartridge seals are preset by the seal
manufacturer and require no field settings. Cartridge seals installed by the user require

«
...
40
41
42
43
44
...
»

Содержание Goulds Pumps API 3171

































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps API 3171

Бренд: Kärcher Страницы: 18

Бренд: Zenit Страницы: 136

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: alkitronic Страницы: 12

Бренд: Daikin Страницы: 316

Бренд: Magic-Pak Страницы: 18

SCP 16000 IQ Level Sensor

Бренд: Kärcher Страницы: 76

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Бренд: Pacific hydrostar Страницы: 36

224342 A Series

Бренд: Graco Страницы: 28

Бренд: SKF Страницы: 12

Бренд: T.I.P. Страницы: 136

WWS120..B Series

Бренд: Vetus Страницы: 32

Бренд: Nakayama Страницы: 29

Бренд: F.B. SUBMERSIBLE MOTORS Страницы: 48

Бренд: Wayne Страницы: 24

Бренд: Little Giant Страницы: 12

Бренд: Flotec Страницы: 16

Бренд: Balboa Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды