ITT Goulds Pumps API 3171 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 64

background image

Introduction and Safety

Model API 3171 Installation, Operation, and Maintenance Manual

3

Introduction and Safety

Introduction

Purpose of this manual

The purpose of this manual is to provide necessary information for:

• Installation

• Operation

• Maintenance

CAUTION:
Failure to observe the instructions contained in this manual could result in personal injury and
property damage, and may void the warranty. Read this manual carefully before installing and
using the product.

NOTICE:
Save this manual for future reference and keep it readily available.

Safety

WARNING:

• The operator must be aware of the pumpage and take appropriate safety precautions to

prevent physical injury.

• Risk of serious injury or death. If any pressure-containing device is over-pressurized, it can

explode, rupture, or discharge its contents. It is critical to take all necessary measures to
avoid over-pressurization.

• Risk of death, serious personal injury, and property damage. Installing, operating, or

maintaining the unit using any method not prescribed in this manual is prohibited.
Prohibited methods include any modification to the equipment or use of parts not provided
by ITT. If there is any uncertainty regarding the appropriate use of the equipment, please
contact an ITT representative before proceeding.

• Risk of serious personal injury. Applying heat to impellers, propellers, or their retaining

devices can cause trapped liquid to rapidly expand and result in a violent explosion. This
manual clearly identifies accepted methods for disassembling units. These methods must
be adhered to. Never apply heat to aid in their removal unless explicitly stated in this
manual.

• If the pump or motor is damaged or leaking, electric shock, fire, explosion, liberation of

toxic fumes, physical harm, or environmental damage may result. Do not operate the unit
until the problem has been corrected or repaired.

• Risk of serious personal injury or property damage. Dry running may cause rotating parts

within the pump to seize to non-moving parts. Do not run dry.

• Risk of death, serious personal injury, and property damage. Heat and pressure buildup

can cause explosion, rupture, and discharge of pumpage. Never operate the pump with
suction and/or discharge valves closed.

• Running a pump without safety devices exposes operators to risk of serious personal

injury or death. Never operate a unit unless appropriate safety devices (guards, etc.) are
properly installed. See specific information about safety devices in other sections of this
manual.

«
...
3
4
5
6
7
...
»

Содержание Goulds Pumps API 3171

































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps API 3171

Бренд: Samson Страницы: 26

Бренд: Danfoss Страницы: 16

Бренд: Raypak Страницы: 40

Бренд: alkitronic Страницы: 12

Бренд: Mueller Страницы: 46

HYDROMATIC SP50

Бренд: Pentair Pool Products Страницы: 12

Бренд: Bard Страницы: 49

Бренд: Grundfos Страницы: 160

Бренд: Lumax Страницы: 28

Бренд: Pentair Jung Pumpen Страницы: 26

Бренд: Accorroni Страницы: 29

Бренд: AMAZON COMMERCIAL Страницы: 48

Бренд: Agilent Technologies Страницы: 306

Бренд: Power Fist Страницы: 20

Бренд: T.I.P. Страницы: 133

Бренд: Spheros Страницы: 55

Бренд: A.O. Smith Страницы: 36

Бренд: Raypak Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды