ITT Goulds Pumps API 3171 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 64

background image

Installation

Model API 3171 Installation, Operation, and Maintenance Manual

19

1. Hex nut
2. Washer
3. Support plate
4. 12.5 mm | 0.5 in. anchor bolt
5. Anchor bolt sleeve
6. Foundation (by customer)

Figure 8: Example of a typical installation

Support plate installation

Install the support plate with a pit cover

If access to the bottom of the pit cover is not possible during the installation process, you must
assemble and install the pump (without the motor), support plate, and pit cover as a unit. You
must install the pit cover perfectly level in order to make sure that the pump remains straight up
and down when installed.
The vapor-proof option includes machined, gasketed fits between the support plate/pit cover
and the pit cover/foundation. You must install these gaskets in order to ensure emissions
performance. Bolt the pit cover to a metal sole plate with a machined surface in order to ensure
an air tight seal.
1. Carefully lower the pit cover onto the foundation bolts.
2. Use as long a level as possible in order to level the pit cover in all directions with shims or

wedges.

3. Hand tighten the anchor bolts. Check the level and re-shim if necessary.
4. Tighten all anchor bolts in a star pattern in order to avoid distorting the pit cover.
5. If access to the bottom side is possible, carefully lower the pump and support plate onto the

pit cover.

6. Install all bolts and hand tighten.
7. Check the level on the support plate and re-shim if necessary.
8. Tighten all bolts in a star pattern in order to avoid distorting the support plate.

Install the support plate without a pit cover

1. Carefully lower the pump and support plate onto the foundation bolts.
2. Level the support plate in all directions using shims and wedges.
3. If you use the vapor-proof option, then perform one of these actions in order to make sure

that you have an air-tight seal:

Support plate
type

Action

Standard

Insert the supplied gasket between the two flanges. Bolt the support plate to a
metal sole plate that has a machined surface.

«
...
19
20
21
22
23
...
»

Содержание Goulds Pumps API 3171

































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps API 3171

Бренд: TapFlo Страницы: 31

Бренд: Danfoss Страницы: 38

AquaMax Eco Expert 21000

Бренд: Oase Страницы: 136

JABSCO 11860 Series

Бренд: Xylem Страницы: 24

Hydro-Guard HG-3

Бренд: Mueller Страницы: 7

ecoTOUGH NRC111-DV-LP

Бренд: Noritz Страницы: 32

Бренд: Daikin Страницы: 316

Бренд: Magic-Pak Страницы: 18

Бренд: EBARA Страницы: 28

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Бренд: Glen Dimplex Страницы: 40

Бренд: BA Pumps & Sprayers Страницы: 18

Бренд: INOXPA Страницы: 19

MONOLITE 320 GT

Бренд: ICI Caldaie Страницы: 36

Бренд: Desmi Страницы: 34

Бренд: Flotec Страницы: 20

MAX-FLO MY1-80 METAL Series

Бренд: Q-MAX Страницы: 15

Weymouth Series

Бренд: Hamworthy Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды