ITT Goulds Pumps API 3171 Скачать руководство пользователя страница 40

Страница: 40 / 64

Maintenance

Model API 3171 Installation, Operation, and Maintenance Manual

Maintenance

Maintenance schedule

Maintenance inspections

A maintenance schedule includes these types of inspections:

• Routine maintenance

• Routine inspections

• Three-month inspections

• Annual inspections

Shorten the inspection intervals appropriately if the pumped fluid is abrasive or corrosive or if
the environment is classified as potentially explosive.

Routine maintenance

Perform these tasks whenever you perform routine maintenance:

• Lubricate the thrust bearings.

• Inspect the seal or packing, if present.

Routine inspections

Perform these tasks whenever you check the pump during routine inspections:

• Check the level and condition of the oil through the sight glass on the bearing frame.

• Check for unusual noise, vibration, and bearing temperatures.

• Check the pump and piping for leaks.

• Analyze the vibration.

• Inspect the discharge pressure.

• Inspect the temperature.

• Check the float controls for the proper setting and operation.

• Check the seal chamber and stuffing box for leaks.

• Ensure that there are no leaks from the mechanical seal.

• Adjust or replace the packing in the stuffing box if you notice excessive leaking.

Three-month inspections

Perform these tasks every three months:

• Check that the foundation bolts are tight.

• Check the packing if the pump has been left idle, and replace as required.

• Check the shaft alignment, and realign as required.

• Check the pump and motor hold down bolts for proper tightness.

Annual inspections

Perform these inspections one time each year:

• Check the pump capacity.

• Check the pump pressure.

• Check the pump power.

If the pump performance does not satisfy your process requirements, and the process
requirements have not changed, then perform these steps:

1. Disassemble the pump.
2. Inspect it.

Содержание Goulds Pumps API 3171

































































Результаты поиска

Содержание Goulds Pumps API 3171

Отзывы:

Похожие инструкции для Goulds Pumps API 3171

Бренды по названию

Популярные бренды

ITT Goulds Pumps API 3171, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps API 3171

Отзывы:

Похожие инструкции для Goulds Pumps API 3171

Бренды по названию

Популярные бренды