irinox ICY L Скачать руководство пользователя страница 12

12

2.12.  R404A GAS SAFETY SHEET

• Identification of dangers

High exposure to inhalation can have anaesthetic 
effects. Very high exposure can cause anomalies of the 
heart beat and cause sudden death. The neubulised or 
sprayed product can cause cold burns to the eyes or 
skin. Dangerous for the ozone layer.

• First aid measures

Inhalation

Move the accident victim away from exposure and keep 
him/her warm and rested. Give oxygen if necessary.
Perform artificial respiration if breathing stops or gives 
signs of stopping. In the case of cardiac arrest, perform 
external cardiac compression.
Request immediate medical assistance.

Contact with the skin

Thaw the affected areas using water.
Remove contaminated clothing.
Attention: clothing can stick to the skin in the case of 
cold burns. In the case of contact with the skin, wash 
immediately with plenty of warm water. If symptoms 
occur (irritation or the formation of blisters) request 
medical assistance.

Contact with the eyes

Wash immediately with an eyewash or clean water, 
keeping the eyelids open for at least 10 minutes. 
Request immediate medical assistance.

Ingestion

Do not induce vomiting.
If the accident victim is conscious, rinse the mouth with 
water and make him/her drink 200-300 ml of water.
Request immediate medical assistance.

Further medical care

Symptomatic treatment and support therapy when 
indicated. Do not give adrenalin and similar 
sympathomimetic drugs following exposure, due to the 
risk of cardiac arrhythmia with possible cardiac arrest.

• Fire-prevention measures

Not inflammable.
The heat decomposition causes the emission of very 
toxic and corrosive vapours (hydrogen chloride, 
hydrogen fluoride). In the case of fire, use respiratory 
aids and suitable protective clothing.

Extinguishers

Use extinguishing agents that are appropriate for the 
fire.

• Use extinguishing agents that are appropriate for 
the fire.

Inhalation

Higher atmospheric concentrations can cause anaesthetic 
effects with possible loss of consciousness.
Very high exposure can cause anomalies of the heart 
beat and cause sudden death.
Higher concentrations can cause asphyxia due to the 
reduced content of oxygen in the atmosphere.

Contact with the skin

Sprays of liquid and the nebulised liquid can cause 
cold burns.
It is improbable that it is dangerous due to cutaneous 
absorption.
Repeated and prolonged contact can cause the removal 
of sebaceous matter, with consequent dryness, cracking 
and dermatitis.

• Ecological information

It decomposes relatively quickly in the lower atmosphere 
(troposphere). The decomposition products are highly 
dispersed and therefore have a very low concentration.
Does not affect photochemical smog (i.e. it does not lie 
within the volatile organic compounds -VOC- according to 
that established by the UN/ECE agreement).
T h e  o z o n e  d e s t r u c t i o n  p o t e n t i a l  ( O D P )  i s  0 . 0 5 5 
measure in comparison with a standard ODP equal to 
1 for the cfc11 (according to uNeP definitions). The 
Global Warming Potential of the gas is 3260.
The substance is governed by the Montreal Protocol 
(revision dated 1992).
The discharges of the product into the atmosphere do 
not cause contamination of waters in the long term.

• Considerations regarding disposal

The best solution consists in recovery and recycling of 
the product.
If this is not possible, destruction must take place in an 
authorised plant equipped to absorb and neutralise the 
acid gases and the other toxic products.

• Measures in the case of accidental leaks

Ensure adequate personal protection (with the use of 
means of protection for the respiratory tract) during the 
elimination of spills.
If the conditions are sufficiently safe, isolate the source 
of the leak. In the presence of spills of modest size, 
leave the material to evaporate on the condition that 
there is suitable ventilation.
Large leaks
-ventilate the area;
-contain the leaking material with sand, earth or other 
suitable absorbent material; 
-prevent the liquid from penetrating drains, sewers, 
basements and work holes, because the vapours can 
create a suffocating atmosphere.

• Handling

Avoid the inhalation of high concentrations of vapours.
The atmospheric concentrations must be reduced to a 
minimum and kept at the minimum level reasonably 
possible, below the professional exposure limit.
The vapours are heavier than the air and therefore the 
formation of high concentrations near to the ground is 
possible, where ventilation is usually low. In these cases, 
ensure adequate ventilation or wear suitable protection 
devices for the respiratory tract with air reserve. Avoid 
contact with naked flames and hot surfaces as irritant and 
toxic decomposition products can be formed. Avoid 
contact between the liquid and the eyes/skin.

Содержание ICY L





































Отзывы: