manualshive.com logo in svg

Incon OPTImizer 2, Руководство пользователя

Поделиться
Скачать
Incon OPTImizer 2 Скачать руководство пользователя страница 42

42

Depending on what is being used to assert the Aux A input, there are multiple methods available to derive the 

A Input Delay

 

setting value.

A Input Assertion

Methods to Derive A INPUT DELAY Setting

1

Parallel connection to “Red 

Light” or trip initiate contacts

• 

Use breaker trip trace, 

A Input Delay

 setting is the time difference between 

the trip initiate signal and the parting of the main contacts

• 

Use ANSI C37.06 to approximate latch release times based on kV level of 

breaker if a breaker trip trace is unavailable

2

Parallel connection to 52 / a  

contact in breaker trip circuit

• 

Use breaker trip trace, 

A Input Delay

 setting is the time difference between 

the opening of the 52 / a  contact and the parting of the main contacts

• 

Use breaker operation time line provided by the manufacturer in Instruction 

literature, provided the 52 / a  contact has not been adjusted from the 

manufacturer

3

Parallel connection to Trip Coil

• 

Use breaker trip trace, 

A Input Delay

 setting is the time difference between 

the opening of the 52 / a  contact and the parting of the main contacts

• 

Use breaker operation time line provided by the manufacturer in Instruction 

literature, provided the 52 / a  contact has not been adjusted from the 

manufacturer

4

Series connection to wetted 

52 / a  contact not in breaker 

trip circuit

• 

Use breaker trip trace, 

A Input Delay

 setting is the time difference between 

the opening of the 52 / a  contact and the parting of the main contacts

• 

Use breaker operation time line provided by the manufacturer in Instruction 

literature, provided the 52 / a  contact has not been adjusted from the 

manufacturer

5

Use of auxiliary relay in 

conjunction with method 1  

• 

Same as method 1, but the delay in pick-up or drop out of the auxiliary relay 

(depending on application) must be added or subtracted from the 

A Input 

Delay

 time setting

6

Use of another input that 

indexes the trip initiate 

contacts

• 

Same as method 1, but the delay in pick-up or drop out of the initiating input 

(depending on application) must be added or subtracted from the 

A Input 

Delay

 time setting

Table 5: Impact of A Input Assertion on the A Input Delay Setting

Содержание OPTImizer 2











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды