Impco HHI Скачать руководство пользователя страница 67

Страница: 67 / 485

Step

Action

Value(s)

Yes



Operate the vehicle within the conditions of
the customer concern.



Monitor the adaptive parameters with the
DST

Do any of the DST readings indicate a lean con-
dition?

Go to Step

(15)

Refer to the

symptom diag-

nostic charts



Turn OFF the ignition.



Relieve the fuel pressure. Refer to the fuel
pressure relief procedure.



Drain any remaining fuel into an approved
gasoline container.



Install the J 37287 Fuel Line Shut-Off Adap-
ters between the rear fuel pipes and the
chassis fuel pipes.



Open the valves on the fuel pipe shut-off
adapters.



Turn ON the ignition, with the engine OFF.



Command the fuel pump relay ON with the
DST or fuel pump test circuit.



Bleed the air from the fuel pressure gage.



Command the fuel pump relay ON and then
OFF with the DST or fuel pump test circuit.



Close the fuel feed pipe shut-off valve.



Monitor the fuel pressure gage for 1 minute.

Does the fuel pressure remain constant?

Go to Step

(17)

Go to Step (9)



Turn OFF the ignition.



Open the fuel feed pipe shut-off valve.



Turn ON the ignition, with the engine OFF.



Command the fuel pump relay ON and then
OFF with the DST or fuel pump test circuit.



Close the fuel return pipe shut-off valve.



Monitor the fuel pressure gage for 1 minute.

Does the fuel pressure remain constant?

Go to Step

(21)

Go to Step

(18)

Is the fuel pressure more than the specified val-
ue?

TBD kPa

(TBD psi)

Go to Step

(12)

Go to Step

(11)

Is the fuel pressure more than the specified val-
ue?

TBD kPa

(TBD psi)

Go to Step

(14)

Go to Step

(15)



Turn OFF the ignition.



Relieve the fuel pressure. Refer to the fuel
pressure relief procedure



Disconnect the rear fuel return pipe from the
chassis pipe.



Attach a length of flexible hose to the chassis
fuel pipe.



Place the open end of the flexible fuel hose
into an approved gasoline container.



Turn ON the ignition, with the engine OFF.



Monitor the fuel pressure gage while the fuel
pump is operating.

Is the fuel pressure within the specified range?

TBD kPa

(TBD psi)

Go to Step

(20)

Go to Step

(13)

Содержание HHI






































































































































































































































































































































































































































































































Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды

Impco HHI, Руководство по обслуживанию

Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды