Impco HHI Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 485

Impco HHI Скачать руководство пользователя страница 35

35

Step

Action

Values

Yes

No

16

Inspect the following for heavy-end deposits:



Electronic Pressure Regulator. Inspect, clean and/or repair
as necessary (refer to EPR Repair Instructions).



Inspect the diaphragm through the Mixer air inlet for any de-
posits or contaminants. DO NOT disassemble the Mixer.
The Mixer is calibrated and disassembly may alter its calibra-
tion and adversely affect engine performance and/or
emissions.

Are all actions complete?

Go to Step

20

NA

17

Replace the ECM.
Is the action complete?

Go to Step

20

NA

18

Replace the Lock-off Valve.
Is the action complete?

Go to Step

20

NA

19

System working correctly at this time. Vehicle may have inter-
mittent electrical connection conditions.



Return vehicle to original condition (but leave the diagnostic
equipment connected).



Start the engine and wiggle test the harness while observing
the DST Faults Screen and the pressure gauge readings.



Repair any conditions encountered.

Is the action complete?

Go to Step

20

NA

20



Clear any active or historic DTCs (DST Service or Faults
Screen).



Clear Adaptive from memory (DST Service Screen).



Return the vehicle to original condition.



Operate the vehicle under all load and driving conditions for
at least 10 minutes.



Park the vehicle with the engine running and connect the
DST to the vehicle’s DLC connector.



Open the GCP software and switch to the Faults Screen.



Let the vehicle idle with no load for at least 30 seconds and
observe the Adaptive 1 fuel correction.

Did the Adaptive 1 fuel correction remain within the specified
values?

-15% to

+15%

Go to Step

21

Go to

Step 24

21

With engine still idling, apply a load with the hydraulic system for
at least 10 seconds and observe the Adaptive 1 value.
Did the Adaptive 1 fuel correction remain within the specified
values?

-15% to

+15%

Go to Step

22

Go to

Step 24

22

Raise the engine rpms to 75-90% of maximum full governed
speed with no load for at least 10 seconds and observe the
Adaptive 1 fuel correction.
Did the Adaptive 1 fuel correction remain within the specified
values?

-15% to

+15%

Go to Step

23

Go to

Step 24

23



With the engine still running at 75-90% of full governed
speed, apply a moderate load with the hydraulic system.



Observe the Adaptive 1 fuel correction.

Did the Adaptive 1 fuel correction remain within the specified
values?

-15% to

+15%

Go to Step

29

Go to

Step 24

24

Was the Adaptive 1 fuel correction less than-15%?

Go to Step

26

Go to

Step 25

«
...
33
34
35
36
37
...
»

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды