Impco HHI Скачать руководство пользователя страница 351

Страница: 351 / 485

351

DTC 1156-Closed Loop Low (Bi-Fuel/Gasoline Only)

Step

Action

Value(s)

Yes



Perform the On-Board (OBD) System Check?

Are any other DTCs present?

Go to Step

(3)

Go to Step

(2)

Visually and physically check the following items:



The air intake duct collapsed or restricted



The air filter for being plugged



The EGO sensor installed securely and the
wire leads not damaged or contacting the
secondary ignition wires



ECM grounds for being clean and tight.



Run the fuel system diagnostic checks

Was a repair made?

Go to Step

(6)

Go to Step

(4)



Diagnose any other DTC codes before pro-
ceeding with this chart.

Have any other DTC codes been detected, diag-
nosed and repaired?

Go to Step

(6)

Go to Step

(4)



Key OFF



Disconnect EGO sensor wire harness connec-
tor CN11



Disconnect ECM wire harness connector CN1



Key ON



Using a DVOM check for voltage at the EGO
connector C11 signal circuit 121 and engine
ground

Do you have voltage?

Repair the

shorted circuit
as necessary.

Refer to Wir-

ing Repairs in

Engine Elec-

trical.

Go to Step

(5)



Replace EGO sensor

Is the replacement complete?

Go to Step

(6)

Содержание HHI






































































































































































































































































































































































































































































































Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды

Impco HHI, Руководство по обслуживанию

Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды