Impco HHI Скачать руководство пользователя страница 193

Страница: 193 / 485

193

DTC 171-Adaptive Learn High (Bi-Fuel/Gasoline Only)

Step

Action

Value(s)

Yes



Perform the On-Board (OBD) System Check?

Are any other DTCs present?

Go to Step

(3)

Go to Step

(2)

Visually and physically check the following items:



The air intake duct for being collapsed or re-
stricted



The air filter for being plugged



System power fuses are good and in the
proper location



The EGO 1 sensor installed securely and the
wire leads not contacting the exhaust manifold
or ignition wires



ECM grounds must be clean and tight. Refer
to Engine Electrical Power and Ground Distri-
bution



Fuel System Diagnostics. Refer to Fuel Sys-
tem Diagnostics

Was a repair made?

Go to Step

(9)

Go to Step

(4)



Diagnose any other DTC codes before pro-
ceeding with this chart. Always repair existing
codes starting with the lowest numerical code
set first.

Have any other DTC codes been detected, diag-
nosed and repaired?

Go to Step

(9)

Go to Step

(4)



Disconnect EGO1 connector CN11



Using a DVOM check for voltage between
EGO 1 connector circuit 812 pin B and engine
ground



Key ON

(CHECK MUST BE MADE WITHIN 30 SECONDS
OR BEFORE POWER RELAY SHUTS DOWN)

Do you have voltage?

System vol-

tage

Go to Step

(5)

Repair the

open EGO

power circuit

as necessary.

Refer to Wir-

ing Repairs in

Engine Elec-

trical.



Key OFF



Disconnect EGO 1 sensor wire harness

connector CN11



Disconnect ECM wire harness connector CN1



Key ON



Using a high impedance DVOM check for
continuity between EGO 1 connector signal
circuit 121 and engine ground

Do you have continuity?

Repair the

shorted circuit
as necessary.

Refer to Wir-

ing Repairs in

Engine Elec-

trical.

Go to Step

(6)

Содержание HHI






































































































































































































































































































































































































































































































Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды

Impco HHI, Руководство по обслуживанию

Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды