Impco HHI Скачать руководство пользователя страница 283

Страница: 283 / 485

283

DTC 359-Fuel Run-out Longer Than Expected

Step

Action

Value(s)

Yes

Did you perform the On-Board (OBD) System
Check?

Go to Step

(2)



Disconnect the LPG shut off solenoid con-
nector CN13



Using a DVOM check for power across ter-
minals (circuits 177 and 821) while cranking
the engine, then turn the key to the OFF posi-
tion.

Did the voltage immediately turn OFF with the
Key cycle?

System Vol-

tage

Go to Step

(3)

Go to Step

(5)



Unplug the LPG Shut-off valve electrical con-
nector.



Start the engine and let it idle until the engine
stops.

(THIS MAY TAKE SEVERAL MINUTES)

Did the engine ever stop?

Intermittent

problem. See

intermittent

problems in

the electrical

section of this

manual.

Go to Step

(4)



Replace the LPG shut off valve.

Is the replacement complete?

Go to Step

(8)



Key OFF



Disconnect the ECM wire harness connector
CN1



Using a DVOM check for continuity between
circuit 177 and engine ground

Do you have continuity?

Repair the

LPG solenoid

control short

to ground

Go to Step

(6)



Inspect the ECM wire harness and connector
for damage corrosion or contamination

Did you find a problem?

Correct the
problem as

required. See

wire harness

repair.

Go to Step

(7)



Replace the ECM

Is the replacement complete?

Go to Step

(8)

Содержание HHI






































































































































































































































































































































































































































































































Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды

Impco HHI, Руководство по обслуживанию

Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды