Impco HHI Скачать руководство пользователя страница 196 | Manualshive

Страница: 196 / 485

Impco HHI Скачать руководство пользователя страница 196

196

DTC 172-Adaptive Learn Low Gasoline (Bi-Fuel/Gasoline Only)

Conditions for Setting the DTC



Heated Oxygen Sensor



Check Condition-Engine Running



Fault Condition-Adaptive multiplier out of range greater than 30%



MIL-On

Circuit Description

The EGO 1 sensor is used to determine if the fuel flow to the engine is correct by measuring
the oxygen content in the exhaust gas. The ECM uses this information to correct the fuel flow
with the Closed Loop multiplier and Adaptive multiplier. This fault will set if the adaptive multip-
lier exceeds the limits of normal operation. Always run the fuel system diagnostic checks
before using the following diagnostic chart.

Diagnostic Aid

Fuel System

The system will be rich if an injector fails to close properly. High fuel pressure

due to a faulty fuel regulator or obstructed fuel return line will cause the system to run rich.

Ignition noise

Open or poor ground circuit to or in the ignition system or ECM wiring may

cause EMI (Electromagnetic interference). This noise could be interpreted by the ECM as igni-
tion pulses or voltage across the oxygen sensor input causing the system to run rich.

MAP Sensor

A higher manifold pressure than normal can cause the system to run rich. Tem-

porarily disconnecting the MAP Sensor will allow the ECM to set a default value for MAP and is
a good way to quickly eliminate this as a problem.

IAT Sensor

Check for a shifted sensor that could cause the ECM to sense lower than actual

temperature of incoming air. This can cause a rich exhaust condition.

ECT Sensor

Check for a “skewed” sensor that could cause the ECM to sense engine tempera-

ture colder than it actually is. This can also cause a rich exhaust condition.

«
...
194
195
196
197
198
...
»

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды