manualshive.com logo in svg

Impco HHI, Руководство по обслуживанию

Поделиться
Скачать
Impco HHI Скачать руководство пользователя страница 477

477

Ethanol:

Grain alcohol (C

2

H

5

OH), generally pro-

duced by fermenting starch or sugar. 

Evaporative Emissions Controls:

An automotive 

emission control system designed to reduce hy-
drocarbon emissions by trapping evaporated fuel 
vapors from the fuel system. 

Excess Flow Valve:

A check valve that is caused 

to close by the fuel when the 

flow exceeds a pr

e-

determined rate. 

FTV:

Fuel Trim Valve. 

FFV

: Flexible Fuel Vehicle. 

Firing Line:

The portion of an oscilloscope pattern 

that represents the total amount of voltage being 
expended through the secondary circuit. 

FMVSS:

Federal Motor Vehicle Safety Standards. 

FPP:

Foot Pedal Position Sensor 

Fuel Injector:

a spring loaded, electromagnetic 

valve which delivers fuel into the intake manifold, 
in response to an electrical input from the control 
module. 

Fuel Lock:

A solenoid-controlled valve located in 

the fuel line to stop the 

flow when the engine 

stops or the ignition switch is off. 

Gasohol:

10 percent ethanol, 90 percent gasoline. 

Often referred to as E-10. 

Gasoline:

A motor vehicle fuel that is a complex 

blend of hydrocarbons and additives. Typical oc-
tane level is 89. 

GCP:

Spectrum III (90-pin) ECM.

Greenhouse Effect:

A scienti

fic theor

y suggesting 

that carbon dioxide from the burning of fossil fuels 
is causing the atmosphere to trap heat and cause 
global warming.

HC:

Hydrocarbon.  An organic chemical compound. 

HD 10:

A fuel of not less than 80% liquid volume 

propane and not more than 10% liquid volume 
propylene. 

HD 5:

A fuel of not less than 90% liquid volume 

propane and not more than 5% liquid volume 
propylene. 

HDV:

Heavy Duty Vehicle.

Heavy Ends:

A term used to describe the buildup

of wax-like impurities that fall out of LPG when
vaporized.

HEGO: 

Heated Exhaust Gas Oxygen, used to de-

scribe a sensor.  Also known as “EGO” (Exhaust 
Gas Oxygen sensor), “O

2

” or “Oxygen sensor.

Hg:

Chemical symbol for the element mercury. 

Used in reference to a measure of vacuum (inch-
es of Hg).

Histogram:

T

he graphical version of a table which 

shows what proportion of values fall into specific
categories over a specific period of time.

Hydrocarbon:

A chemical compound made up of 

hydrogen and carbon (HC).  Gasoline and almost 
all other fuels are hydrocarbons. 

Hydrostatic Relief Valve:

A pressure relief device 

installed in the liquid LPG hose on a LPG fuel 
system. 

IAT:

Intake Air Temperature 

Ideal Mixture:

The air/fuel ratio at which the best 

compromise of engine performance to exhaust 
emissions is obtained. Typically 14.7:1. 

Ignition Reserve:

The difference between availa-

ble voltage and the required voltage. 

ILEV:

Inherently Low Emission Vehicle.

IMPCO:

Imperial Machine Products Company.

IMPCO Technologies, Inc.

A manufacturer of both 

LPG and Gasoline fuel systems. 

Impedance

: A form of opposition of AC electrical 

current 

flow (resistance) measured in ohms. 

Insulation:

A nonconductive material used to cover 

wires in electrical circuits to prevent the leakage 
of electricity and to protect the wire from corro-
sion. 

Intercept:

An electrical term for a type of splice 

where the original circuit is interrupted and redi-
rected through another circuit. 

ITK:

IMPCO Test Kit 

Knock:

Sound produced when an engine’s air/fuel 

mixture is ignited by something other than the 
spark plug, such as a hot spot in the combustion 
chamber. Also caused by a fuel with an octane 
rating that is too low and/or incorrect ignition tim-
ing.  Also called detonation or ping. 

Lambda Sensor:

A feedback device, usually lo-

cated in the exhaust manifold, which detects the 
amount of oxygen present in exhaust gases in re-
lation to the surrounding atmosphere.  (See 
HEGO).

LDV:

Light Duty Vehicle. 

Lean Mixture:

An air to fuel ratio above the stoi-

chiometric ratio; too much air

.

LEV:

Low Emission Vehicle

.

Limp-in or Limp Home:

  A mode where the ECM 

or a component has failed, but the vehicle re-
mains operational although the engine may 
operate minimally.  This term may also describe 
the drivability characteristics of a failed computer 
system.

Liquid Petroleum Gas (LPG):

A fuel commonly 

known as propane consisting mostly of propane 
(C

3

H

8

), derived from the liquid components of 

natural gas stripped out before the gas enters the 
pipeline, and the lightest hydrocarbons produced 
during petroleum re

fining. Octane level of LPG is 

107.

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды