Impco HHI Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 485

Impco HHI Скачать руководство пользователя страница 66

66

GASOLINE FUEL SYSTEM DIAGNOSTIC CHART

Step

Action

Value(s)

Yes

No

1

Did you perform the On Board (OBD) System
Check?

-

Go to Step

(2)

Go to OBD

System Check

Section

2

Important: Inspect the fuel system for damage or
external leaks before proceeding with this diag-
nostic.



Turn ON the ignition, with the engine OFF.



Command the fuel pump ON with the DST or
fuel pump test circuit.

Does the fuel pump operate?

Go to Step

(3)

Check all sys-

tem power

fuses and

power relay

circuit. Refer to

wiring harness

schematic.

3

Important: Verify that adequate fuel is in the fuel
tank before proceeding with this diagnostic.



Turn OFF the ignition.



Turn OFF all accessories.



Install the fuel pressure gage.



Turn ON the ignition, with the engine OFF.

(The fuel pump relay may need to be com-
manded ON a few times in order to obtain the
highest possible fuel pressure)



DO NOT start the engine.



Command the fuel pump ON with the DST or
fuel pump test circuit.



Observe the fuel pressure gage with the fuel
pump commanded ON.

Is the fuel pressure within the specified range?

TBD-TBD

kPa (TBD-

TBD psi)

Go to Step

(4)

Go to Step

(10)

4

Important: The fuel pressure may vary slightly
when the fuel pump stops operating. After the
fuel pump stops operating, the fuel pressure
should stabilize and remain constant.



Monitor the fuel pressure gage for 1 minute.

Does the fuel pressure decrease by more than
the specified value?

TBD-TBD

kPa (TBD-

TBD psi)

Go to Step

(8)

Go to Step (5)

5



Relieve the fuel pressure to the first specified
value.



Monitor the fuel pressure gage for 5 minutes.

Does the fuel pressure decrease by more than
the second specified value?

TBD-TBD

kPa (TBD-

TBD psi)

Go to Step

(22)

Go to Step (6)

6



Turn ON the ignition, with the engine OFF



Monitor the fuel pressure gauge



Start the engine

Does the fuel pressure decrease by the specified
value when the engine is started?

TBD-TBD

kPa (TBD-

TBD psi)

Go to Step

(7)

Go to Step

(21)

«
...
64
65
66
67
68
...
»

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды