Impco HHI Скачать руководство пользователя страница 458 | Manualshive

Страница: 458 / 485

Impco HHI Скачать руководство пользователя страница 458

458

PROTECTION OF ELECTRICAL COMPONENTS

To prevent permanent damage to the ECM
and/or other electrical components, follow-
ing the steps listed below

1. ALWAYS turn ignition to OFF prior to removing

the harness and/or the negative or positive
battery cable.

2. ALWAYS disconnect the negative and positive

battery cable (Remove the negative cable first)
when welding on a vehicle.

3. NEVER use a charger or voltage supply in

excess of 16 volts.

I. ENGINE CONTROL MODULE

This procedure relates to removal and installation
of the ECM--see Diagnostic Scan Tool for access-
ing ECM software.

REMOVAL PROCEDURE

1. Disconnect Negative battery cable.
2. Push connector lock back to unlock connector,

unplug the Wire Harness from ECM and re-
move.

3. Remove four bolts mounting the controller to

the mounting bracket.

ECM and its Four Mounting Bolts

INSTALLATION PROCEDURE

IMPORTANT
The ECM is calibrated for each engine. Verify you
have the correct controller by noting the P/N on the
ECM label. The calibration number can also be
found by connecting the DST and finding the calibra-
tion number on the Gauge Page.

1. Mount controller into mounting bracket with four

screws.

Torque to 7.5

Nm

(5.5 ft. lbs.)

2. Plug connector into controller.

3. Push lock into place.

4. Reconnect the negative battery cable.
5. Install Diagnostic Service Tool.

6. Start the vehicle and let run until it reaches nor-

mal operating temperature.

7.

If a DTC code is found, refer to the Electrical
Section for further diagnosis.

II. ENGINE WIRE HARNESS REPLACEMENT

1.

Disconnect negative battery cable.

2. Lay out the new wire harness, noting the loca-

tion, type of connectors, and identifying
markings. Take special note of identical or simi-
lar connectors (such as the coils or HEGO
Sensors) to avoid crossing connections during
installation. Note the routing of the existing wire
harness in and around the engine and the ve-
hicle. Refer to the Electrical Schematic.

Ensure that all connections are made to the
correct locations on the engine and its com-
ponents. Crossing connections may cause
poor engine performance, a MIL warning
and/or permanent damage to the ECM.

3. Remove all wire harness connectors on the ve-

hicle.

4. Remove all clips and brackets holding the wire

harness and remove harness from vehicle.

5. Lay the new wire harness over the engine and

route each end to its connection. Verify that all
connectors match prior to installation.

6. Connect all connectors and ring terminals.
7. Install all clips and brackets to hold down the

harness.

8.

Reconnect negative battery cable.

«
...
456
457
458
459
460
...
»

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды