manualshive.com logo in svg

Impco HHI, Руководство по обслуживанию

Поделиться
Скачать
Impco HHI Скачать руководство пользователя страница 461

461

TMAP Sensor

INSTALLATION PROCEDURE 

1. Install the TMAP and

torque the retaining 

screw to

19 in.lbs. (2.1 Nm).

2.

Reconnect the negative battery cable.

3. Start the vehicle and let run until it reaches 

normal operating temperature.

4.

If a DTC code is found, refer to the Electrical 
Section for further diagnosis.

VII.  ENGINE COOLANT TEMPERATURE 

SENSOR (ECT)

REMOVAL PROCEDURE

1. Disconnect the negative battery cable. 

2. Locate the Engine Coolant Temperature Sen-

sor on the back of the engine (opposite end of 
the fan).

Location of the Water Temperature Sensor

3. Remove electrical connector.
4. Drain the cooling system.

5. Remove the sensor.

INSTALLATION PROCEDURE 

1. Apply a minimal amount of Loctite 962T or 

equivalent sealer to threads on the Engine Coo-
lant Temperature Sensor.  Remove any excess 
sealer on the sensor threads.

2.

Install Engine Coolant Temperature Sensor.  

Torque to 

10.8-14.5 ft.lbs. (14.7-19.6 Nm).

3. Refill the cooling system.

4.

Reconnect electrical connector.

5. Reconnect the negative battery cable.

6. Start the vehicle and let run until it reaches nor-

mal operating temperature.

7.

If a DTC code is found, refer to the Electrical 
Section for further diagnosis.

VIII. HEATED EXHAUST GAS OXYGEN SENSOR 

(HEGO) 

REPLACEMENT

1. Disconnect Negative battery cable.
2. Locate the affected Oxygen Sensor on the three 

way catalytic converter/muffler assembly.  There 
are two sensors: one between the engine and 
catalytic brick (upstream) and one between the 
catalytic brick and tail pipe (downstream). 

3. Disconnect the Oxygen sensor electrical connec-

tor. 

HEGO and Connector

4. Using an Oxygen Sensor socket, remove the 

Oxygen Sensor. 

INSTALLATION PROCEDURE

IMPORTANT 
Before install the Oxygen sensor lubricate threads 
with anti-seize compound P/N 5613695 or equiva-
lent.  Avoid contaminating sensor tip with 
compound.

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды