manualshive.com logo in svg

Impco HHI, Руководство по обслуживанию

Поделиться
Скачать
Impco HHI Скачать руководство пользователя страница 37

37

ADDITIONAL STEPS

Step

Action

Value(s)

Yes

No

1

1.

Perform the On-Board Diagnostic (OBD) System check.

Are any DTCs present in the ECM?

Go to Ap-

plicable 

DTC Ta-

ble

Go to 

Step 2

2

Has the Fuel system diagnosis been performed? 

Go to 

Step 3

Go to 

Fuel 

system 

Diagno-

sis

3

1.

Replace the Engine Control Unit (ECM). Refer to Engine 

Control Unit (ECM) replacement.
Is this action complete?

Go to 

Step 5

Go to

Step 4

4

1.

Repair the open or damaged circuit.

Is this action complete?

Go to 

Step 5

Go to 

Step 8

5

1.

Return the fuel system to normal operating condition. 

2.

Observe the Adaptive 1 fuel correction.

3.

Raise the engine speed to approximately 2500 rpm.

Is the Adaptive 1 fuel correction within the specified range at 
idle and 2500 rpms?

-15 to 

+15

Go to 

Step 9

Go to 

Step 6

6

1.

Check all vacuum hoses and mixer connections for lea-

kage.
Was a problem found?

Go to 

Step 5

Go to 

Step 7

7

1.

Replace Mixer.

Is this action complete?

Go to 

Step 5

Go to 

Step 9

8

1.

The fuel control system is operating normally. Refer to 

Symptoms Diagnosis 1. Disconnect all test equipment 2.
2.

If you were sent to this routine by another diagnostic chart, 

retune to the previous diagnostic procedure.
Is this action complete?

System 

OK

9

1.

Disconnect all test equipment 

2.

Start the engine 

3.

Using a liquid leak detection solution leak check any fuel 

system repairs made.
Is this action complete?

System 

OK

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды