Impco HHI Скачать руководство пользователя страница 421

Страница: 421 / 485

421

DTC 2139-FPP 1 Lower Than IVS Limit

Step

Action

Value(s)

Yes

Did you perform the On-Board (OBD) System
Check?

Go to Step

(2)

Go to OBD

System

Check Sec-

tion



Key ON, Engine OFF



DST (Diagnostic Scan Tool) connected in
System Data Mode

Does the DST display IVS voltage less than 1.00
volts with the foot pedal in the idle position?

Greater than

1.00 volt

Go to Step

(5)

Go to Step

(3)



Observe the FPP and IVS voltages



Stroke the pedal while observing the voltage
readings

Does FPP voltage drop below 0.85 volts at any
time while the IVS reads less than 1.0 volt?

FPP less

than 0.85

volts AND

IVS less

than 1.0 volt

Go to Step

(4)

Intermittent

problem

Go to Inter-

mittent

section



Disconnect the System Interface connector
CN21



Check for continuity between circuits 153
and 120 at the system interface connector
CN21

Do you have continuity?

Repair circuit

as necessary.

See wiring

harness re-

pair section.

Go to Step

(6)



Disconnect the System Interface connector
CN21



Check for continuity between circuits 154
and 120 at the system interface connector
CN21

Do you have continuity?

Repair circuit

as necessary.

See wiring

harness re-

pair section.

Go to Step

(6)



Disconnect the ECM connector CN1



Check for continuity on the sensor ground
circuit 120 between the system interface
connector CN21 and the ECM connector
CN1

Do you have continuity on the circuit?

Go to Step

(7)

Repair circuit

as necessary.

See wiring

harness re-

pair section.



Inspect the FPP/IVS connector, the ECM
connector CN1, and the system interface
connector CN21 for damage, corrosion, or
contamination.

Any damage found?

Repair circuit

as necessary.

See wiring

harness re-

pair section.

Go to Step

(8)

Содержание HHI






































































































































































































































































































































































































































































































Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды

Impco HHI, Руководство по обслуживанию

Результаты поиска

Содержание HHI

Отзывы:

Бренды по названию

Популярные бренды