Impco HHI Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 485

Impco HHI Скачать руководство пользователя страница 59

59

code and by using the diagnostic charts in this
manual to determine the cause of the malfunc-
tion. In the event a technician does not have the
computerized diagnostic tool, the MIL light can be
used to identify the diagnostic code to activate
the “blink” feature and count the number of blinks
to determine the diagnostic code number to lo-
cate the fault in the system.

HEATED EXHAUST GAS OXYGEN SENSORS

The Heated Exhaust Gas Oxygen (HEGO) Sen-
sors are mounted in the exhaust system, one
upstream and one downstream of the catalytic
converter. The HEGO sensors are used to
measure the amount of oxygen present in the ex-
haust stream to determine whether the fuel air
ratio is to rich or to lean. It then communicates
this measurement to the ECM. If the HEGO sen-
sor signal indicates that the exhaust stream is too
rich, the ECM will decrease or lean the fuel mix-
ture during engine operation. If the mixture is too
lean, the ECM will richen the mixture. If the ECM
determines that a rich or lean condition is present
for an extended period of time which cannot be
corrected, the ECM will set a diagnostic code and
turn on the MIL light in the dash.

By monitoring output from the sensor upstream
and the sensor downstream of the catalytic con-
verter, the ECM can determine the performance
of the converter.

The Heat Exhaust Gas Oxygen (HEGO) Sensor

HEGO1 (upstream or before the catalytic con-
verter) and HEGO2 (downstream) voltage
output.

The Heated Exhaust Gas Oxygen Sensor
(HEGO) is an emissions control compo-
nent. In the event of a failure, the HEGO
should only be replaced with the recom-
mended OEM replacement part. The
HEGO is sensitive to silicone based prod-
ucts and can become contaminated.
Avoid using silicone sealers or air or fuel
hoses treated with a silicone based lubri-
cant.

TMAP SENSOR

T–MAP Sensor

The Air Temperature/Manifold Absolute Pressure
or TMAP sensor is a combination of two sensors:

1) A variable resistor used to monitor the differ-

ence in pressure between the intake manifold
and outside or atmospheric pressure. The
ECM monitors the resistance of the sensor to

«
...
57
58
59
60
61
...
»

Содержание HHI






































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды