background image

900861-00D

31

IHP.us.com

Error Codes

The control module has the ability to detect problems with the valve 

kit system and will initiate error codes when they occur.  The error 

codes listed below will guide you to solving troubleshooting issues.

Ignition Safety Error: One short beep every one second. 

Cause: Pilot did not light within the trial period of 50-60 seconds 

therefore step motor will turn gas valve to OFF position.

Corrective Action: Press OFF button to clear. Wait 30 seconds and 

try again.

Recycle Safety Error: Two short beeps every one second.

Cause: 1. Pilot automatically lights and drops out 3-times within 

2-minutes causes step motor to turn gas valve to OFF position. 2. 

Someone has pressed the ON/OFF button 6-times within 2-min-

utes causing the step motor to turn gas valve to OFF position.

Corrective Action: Press OFF button to clear. After 5-minutes the 

beeping will stop then retry.

Sensor Safety Error: Four short beeps every one second (constant 

ERROR CODE TROUBLESHOOTING

OPTIONAL ACCESSORIES

PRODUCT REFERENCE INFORMATION

Cat. No.

Model#

Description

F3502

LPK 1

LP Conversion kit for 36-inch outdoor fireplace

F3503

LPK 2

LP Conversion kit for 48-inch outdoor fireplace

F3504

LPK 3

LP Conversion kit for 60-inch outdoor fireplace

F3505

LPK 4

LP Conversion kit for 72-inch outdoor fireplace

F3507

GLO-BLACK

Black Onyx Glass Media, 5lb

F3508

GLO-CRYSTAL

Diamond Crystal Glass Media, 5lb

F3509 

GLO-LT BLUE

Sapphire Blue Glass Media, 5lb

Remote Control Kit

Cat. No.

Model#

Description

F2687

EF-BRCK

Remote Control, Manual ON/OFF opera-

tion, Off / Continuous pilot feature

Ecoflow Control Kits

Cat. No.

Model#

Description

F2660

EF-WWRCK

Wireless Wall Switch, On/Off, High/Low

ON

OFF

HI

LOW

Continuous Pilot

ON/OFF

beeping).

Cause: Pilot flame sensor voltage too high, ground circuit not 

properly connected, pilot ground wire loose or not connected, or 

motor not plugged into control module; therefore, step motor will 

turn gas valve to OFF position.

Corrective Action: Press OFF button to clear. Wait 30-seconds to 

thermocouple to cool down. If persist, then check other possible 

causes and retry.

Thermal Safety: Four short beeps every two seconds.

Cause: System has overheated and exceeded 170°F internal tem-

perature limit and the step motor will turn gas to OFF.

Corrective Action:  Internal temperature must cool down to below 

160°F then press the OFF button to clear and retry.

Communication Safety: One short beep every four seconds.

Cause: Transmitter and module are not communicating properly. 

Could be related to distance greater than 20-feet away from each 

other or weak/dead batteries in one or the other.

Corrective Action: Module must receive a signal from transmitter.

Product Reference Information

Linear Electronic 

VF Outdoor Fireplaces

Cat. No.

Model

F4493

ODLVF36ZEN

F4494

ODLVF48ZEN

F4495

ODLVF60ZEN

F4496

ODLVF72ZEN

ON

OFF

HI

LO

OPTIONAL ACCESSORIES CONT.

Содержание ODLVF36ZEN











































Отзывы: