IHP ODLVF36ZEN Скачать руководство пользователя страница 19

Страница: 19 / 42

900861-00D

IHP.us.com

Step 10: Remove the RGB control box from the components parts

carton. The fireplace is supplied with 10-feet of wiring for the

RGB control box (switches and dimmer) installation. Find a suit-

able location within a close proximity of the fireplace for conve-

nience of operation and mount the control box upright and level

as shown in Figure 27. Use Figures 25 and 26 for dimensional

reference.

CAUTION: ENSURE ALL SWITCHES ARE IN THE OFF POSITION.

“I” INDICATES IGNITE/ON AND “O” INDICATES OFF. LEARN BUT-

TON DOES NOT APPLY.

Step 11: Remove the four (4) outer screws from each corner in-

side the cover plate and lift off. See Figure 25. This will expose

the mounting plate. See Figure 26. CAUTION: DO NOT REMOVE

THE TWO CENTER SCREWS FROM THE COVER PLATE. THIS WILL

RELEASE THE ENTIRE SWITCH BOX WIRING FROM INSIDE THE

JUNCTION BOX AND MAKE IT DIFFICULT TO REINSTALL.

Take note of the 8-PIN and 6-PIN wire connectors. These are la-

beled LED lights (6-PIN) and Control Module (8-PIN) connections.

These will be the final connection to the fireplace and crucial to

the operation.

Figure 25 - RGB Control Box with 8-3/4” x 8-3/4” Cover Plate

Figure 26 - RGB Control Box Mounting Plate

Step 12: Mount the RGB control box into the desired location.

CAUTION: AVOID USING EXCESSIVE FORCE WHEN INSTALLING

ANY CONNECTORS.

Step 13: Remove the 8-PIN module wire harness (Cat. No.

F3500) from the components part box. Locate the 8-PIN male

connector from the valve box (under the fireplace) and connect

it to the 8-PIN female end of the wire harness. Connectors only

attach one way; press together until it snap locks into place. See

Figure 27 for details.

Step 14: Feed the other end of the wire harness through the

square access hole underneath the fireplace and pass the GFCI

box, outside the fireplace to the RGB control box and connect.

Connectors only attach one way; press together until it snap locks

into place.

Step 15: Locate the two 1/4” male terminals from the valve box

and connect the AF-4000ADP24 adaptor (Cat. No. F3482). Plug

the 7.5VDC adaptor into the 120VAC GFCI box.

Step 16: Locate the 6-PIN wire harness (Cat. No. F3500) for the

LED lights and feed the wire harness up to the RGB control box

and attach. Connectors only attach one way; press together until

it snap locks into place. See Figure 27.

LED LIGHTING INSTALLATION

Continued

RGB DIMMER

Cover Plate Surrounding Switch Plate

Remove screws to mount switch plate

LED

ON/OFF

LOW

HIGH

LEARN

CONT.

PILOT

RGB DIMMER

Mounting plate under switch cover

LED

ON/OFF

LOW

HIGH

LEARN

CONT.

PILOT

5-5/8”

(143mm)

5-5/8”

(143mm)

Содержание ODLVF36ZEN











































Результаты поиска

Содержание ODLVF36ZEN

Отзывы:

Похожие инструкции для ODLVF36ZEN

Бренды по названию

Популярные бренды

IHP ODLVF36ZEN, Инструкции по сборке, установке и эксплуатации

Результаты поиска

Содержание ODLVF36ZEN

Отзывы:

Похожие инструкции для ODLVF36ZEN

Бренды по названию

Популярные бренды