IHP ODLVF36ZEN Скачать руководство пользователя страница 4

Страница: 4 / 42

IHP.us.com

900861-00D

1. These fireplaces are designed for outdoor use only. Not ap-

proved for any indoor use.

2. We recommend using 3/4” black iron pipe; however please

refer to the National Fuel Gas Code, ANSI Z223.1/ NFPA 54

(USA) - latest edition or CAN/CGA-B149.1 Natural Gas And

Propane Installation Code (Canada) - latest edition for proper

pipe sizing when exceeding 20-feet in length for fireplaces .

3. Determine which fireplace you are preparing to install, sin-

gle-sided or see-through

(refer to

Page 8

11)

4. This fireplace is not a “load bearing” fireplace. All finishing

materials must be supported by the surrounding structure and

not rely on the fireplace itself.

5. Follow the local code requirements for the gas type being

used. This fireplace should be installed in accordance with

local codes and ordinances or in the absence of local codes,

with the National Fuel Gas Code, ANSI Z223.1/ NFPA 54

(USA) - latest edition or CAN/CGA-B149.1 Natural Gas And

Propane Installation Code (Canada) - latest edition.

6. Fireplaces create high temperatures, it is very important to

have any combustibles at a safe distance.

7. Fireplace should never be left unattended while in opera-

tion. It should always be a safe distance from all trees and

combustible landscape materials.

8. The fireplace must be installed on a flat, level, stable, non-

combustible surface.

Exception

: It is permissible to place

one layer of 1/2” cement board underneath the entire fire-

place, then it may sit on a flat, level, stable, combustible

surface. Drainage is critical to ensure that water does not

damage gas valve and components.

Never install the

fireplace system below grade.

9. CAUTION:

A minimum of 18 square inches of cross ventilation

(per side) is required to keep the inside of the enclosure dry.

Install the supplied VENT-KIT-6x12 (cat. no. F3535) approxi-

mately 3 to 4 inches from the floor centered on each end of

the fireplace

(See

Figure 3, Page 5

10. Never fill the cavity under and around the valve box with any

material, this is air space necessary for ventilation.

11. Only non-combustible materials (i.e. metal studs and ce-

ment board) should come in direct contact with any part of

the fireplace. Underneath area should be non-combustible or

a flat level combustible surface according to the clearances

specified in this manual. Bend out nailing flanges on ends

of fireplace and secure to metal studs.

12. This fireplace is designed to have glass media covering the

burner trough, so the burner tube is not visible. Use only the

media provided with the appliance or listed in the accessory

section of this manual

(Page 31)

DO NOT COVER THE IGNI-

TION HOOD WITH THE GLASS MEDIA.

See

Figures 33 and 34

Pages 23 and 24

for details.

13. Gas lines and fittings must be installed into the non-combus-

tible structure. All gas connections must be leak tested be-

fore installation of the fireplace. Leak detection is required

before regular use of the fireplace.

14. Do not use alternative media that will absorb moisture over

time and will not release this moisture quickly. Moisture

can boil in this media and can rapidly break apart and cause

property damage or personal injury.

15. Never leave any other combustible material on top of the

fireplace. This could cause unsafe operation of this system

and damage to the component that will not be covered under

our warranty.

16. It is recommended to wear gloves when moving the fireplace

into position and watch for sharp edges when handling the

fireplace.

WARNING

These fireplaces are gas fireplaces. Do not burn wood or other

material in these appliances.

WARNING

These appliances are not designed or intended to be used for

cooking. Do not barbecue, heat food, or roast marshmallows in this

appliance. Doing so could damage the appliance and cause injury.

INSTALLATION PRECAUTION:

This fireplace requires a minimum 18-square inches

(per side) of cross ventilation. Failure to provide

proper ventilation can void the warranty.

INSTALLATION PRECAUTIONS

Содержание ODLVF36ZEN











































Результаты поиска

Содержание ODLVF36ZEN

Отзывы:

Бренды по названию

Популярные бренды

IHP ODLVF36ZEN, Инструкции по сборке, установке и эксплуатации

Результаты поиска

Содержание ODLVF36ZEN

Отзывы:

Бренды по названию

Популярные бренды