IHP ODLVF36ZEN Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 42

background image

IHP.us.com

900861-00D

26

FINAL PREPARATION

Continued

CAUTION: THIS IS TEMPERED GLASS. DO NOT CHIP GLASS.

CHIPPED TEMPERED GLASS CAN BREAK WITHOUT WARNING

.

Figure 40 Installing glass panels.

Figure 39 Glass clips location.

GLASS WINDSHIELD

Glass Holders

INSTALLING REMAINING GLASS CLIPS

Step 26:

Install the remaining (2) glass clips in front of the LED

clips as described on

page 16 in Steps 3 and 4, Figures 18 and

19.

GLASS PANEL/WINDSHIELD INSTALLATION

Step 27:

• Carefully unpack the glass panels.

• Using gloves carefully lift one glass panel, into the fireplace

opening, over top of the glass clips, and slide it down into

the metal retainer clip, supporting the glass at the top and

bottom as you handle it.

See Figure 40.

As the glass enters

the clip the bottom edge of the glass will rest in place on the

bottom of the clip.

• Install the second glass pane in the same manner as de-

scribed in

Figure 40.

• Both glass panels should be level when installed.

• Center glass between clips after installation.

Step 1

Step 2

Front of Fireplace

LED

HOT GLASS WILL

CAUSE BURNS

DO NOT TOUCH

GLASS UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the

protection of children and other at-risk

individuals.

DANGER

“WARNING: Both glass panels must be installed when the fire-

place is in operation”. Note:

All four (4) glass panels must be

installed on see through fireplaces.

«
...
24
25
26
27
28
...
»

Содержание ODLVF36ZEN











































Отзывы:

Нет отзывов

Похожие инструкции для ODLVF36ZEN

Бренд: Napoleon Страницы: 4

Бренд: LA NORDICA Страницы: 80

Бренд: Waterford Страницы: 24

Бренд: RAIS Страницы: 108

Valor Legend Ultra 837 AN

Бренд: Valor Страницы: 12

Ascent Multi-View Series

Бренд: Napoleon Страницы: 70

Smart Bell 65/55 MF

Бренд: Bellfires Страницы: 48

Бренд: KENT Страницы: 2

Бренд: Travis Industries Страницы: 2

Бренд: Greentouch Страницы: 42

Бренд: Woodbridge Страницы: 40

Бренд: Enviro Страницы: 47

Бренд: cye-way Страницы: 8

Бренд: pleasant hearth Страницы: 15

AURA Fire Table

Бренд: Seaside Casual Страницы: 2

Бренд: tropitone Страницы: 4

Бренд: JAYLINE Страницы: 11

Бренд: Lennox Hearth Products Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды