manualshive.com logo in svg

IHP ODLVF36ZEN, Инструкции по сборке, установке и эксплуатации

Поделиться
Скачать
IHP ODLVF36ZEN Скачать руководство пользователя страница 30

IHP.us.com

900861-00D

30

Symptom

Remedy

Fireplace Won’t Light

1. Bleed gas line.

2. Ensure all gas lines are turned ON.

3. Ensure there is not too much media overtop the burner, it can inhibit the gas flow.  Too little 

or no media can also contribute to non-lighting.

4. Ensure adaptor is plugged in.

5. Verify 120VAC power at junction box under burner pan.

6. Media blocking pilot hole.  See Figure 34 on Page 24.

No Spark to Ignite

1. Visually look at igniter for any physical damage.

2. Ensure adaptor is plugged in and reads 7.5VDC

Continues to Spark after Lighting 1. Thermocouple out of alignment.

2. Check connection of thermocouple at “S” terminal on control module to ensure it is con-

nected.

Low Flame

1. Use only glass media provided with appliance or listed in the accessory section of this manual 

(see Page 31). Ensure that the media is no more than 1-inch over top of burner.

2. Ensure all shutoff valves are is fully open (see Page 5, Figure 1).

3. Check for spider webs inside burner orifice.

4. Check gas pressure.

Water in my Fireplace

1. Excess dust/sand material from media may be blocking the weep holes to relieve water.  Re-

move all media and unplug weep holes.  Clean or install new media free of dust and dirt.

2. Ensure fireplace has proper drainage for water and proper ventilation to dry out.

Whistling Noises

1. Check media to ensure it is not too tightly packed around the burner tube.

2. Ensure a non-whistling flex connector is being used.

Fireplace Won’t Stay Lit

1. Check alignment of pilot flame through ignition hole on Page 25, Figure 34.

2. Thermocouple reading should be between 10-20mV.  Test at the brass ground lead on gas 

valve and the gold lead at “S” terminal on the control module. If no minimum millivolts are 

maintained replace the TC. Must test with pilot running to obtain readings.

3. Check continuity of thermocouple.  Using a volt meter remove the TC test lead “S” from the 

control module and the brass fork terminal from the gas valve.  Test for continuity.  If no con-

tinuity then replace the TC.

4. Ensure thermocouple is clean and free of any debris.  Excessive soot can be an issue.

Low Flame Height

1. Wrong media installed into the burner trough.

2. Too much media installed overtop of the trough (See Page 25, Figure 36 for details).

Sooting

1. Incorrect gas for the fireplace.  Ensure rating label has proper model number for gas being 

used.

2. Too much media can cause sooting.

3. Wrong media being used. (See Page 25 for details).

GENERAL TROUBLESHOOTING

Содержание ODLVF36ZEN











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды