IHP ODLVF36ZEN Скачать руководство пользователя страница 33

Страница: 33 / 42

900861-00D

IHP.us.com

GAS CONVERSION INSTRUCTIONS

Step 1. Turn OFF the gas supply to the outdoor fireplace and dis-

connect any electrical power.

Step 2. Remove the burner pan from the fireplace to enable con-

version access. See installation manual if necessary.

Step 3. Disconnect the flex line at the main burner orifice. Then

remove the orifice and flared fitting from the orifice. Re-tape the

flared fitting with the new OAS-LP orifice per Table 8. Ensure to

use gas rated Teflon tape around the threads or pipe compound.

Check for leaks after conversion is complete.

Step 4. Locate the gas regulator on the opposite side of the valve

box. Using a regular size flat bladed screwdriver to remove the

aluminum cap and washer from the regulator. See Figure 46.

NOTE: The plastic stem has a marking on it with an arrow. Look

carefully on the stem, it may be difficult to read.

The gas type is determined with the arrow pointing at the alumi-

num cap as seen in Figures 47 and 48.

Step 5. On the underneath side of the aluminum cap is a plastic

stem. Using a 6mm wrench remove the stem, unscrew the stem

(counter-clockwise

), turn it over and install the opposite

end back into the cap. See Figure 47.

NATURAL GAS TO PROPANE GAS CONVERSION

Continued

Model

Main Burner Orifice

Low Rate Set Screw

LPK1 (36” Fireplace)

OAS-LP52

ECO-LSS-52

LPK2 (48” Fireplace)

OAS-LP48

ECO-LSS-46

LPK3 (60” Fireplace)

OAS-LP44

ECO-LSS-42

LPK4 (72” Fireplace)

OAS-LP42

ECO-LSS-35

Table 8 - Reference Information

Figure 45 - Changing Main Burner Orifice

Figure 46 - Regulator cap location

Regulator

Aluminum

Cap

Regulator

Aluminum Cap

Figure 47 - Regulator stem shown in NG setting

Regulator

Plastic Stem

Regulator

Plastic Stem

Regulator

Plastic Stem

Figure 48 - Regulator stem shown in LP setting

Regulator

Plastic Stem

Gas Shut-off

Regulator

Содержание ODLVF36ZEN











































Результаты поиска

Содержание ODLVF36ZEN

Отзывы:

Бренды по названию

Популярные бренды

IHP ODLVF36ZEN, Инструкции по сборке, установке и эксплуатации

Результаты поиска

Содержание ODLVF36ZEN

Отзывы:

Бренды по названию

Популярные бренды