IBM Power Systems Series Скачать руководство пользователя страница 31

Страница: 31 / 134

Replace the PCIe adapter. Go to “5104-22C or 9006-22C locations” on page 63 , “9006-12P locations”

on page 75, or “9006-22P locations” on page 91 and use the slot number information in the operating

system log to identify the physical location and the removal and replacement procedure.

Identifying the location of the NVMe Flash adapter

Use this procedure to identify the location of a Non-Volatile Memory Express (NVMe) Flash adapter.

Procedure

1. Does the operating system log contain the slot number? For example, the log might contain an error

message similar to the following text:

[131779.752714] EEH: PHB#0 failure detected, location: WIO-R Slot

Then

Yes:

Replace the adapter. Go to “5104-22C or 9006-22C locations” on page 63,

“9006-12P locations” on page 75, or “9006-22P locations” on page 91 and use the

slot number information to identify the physical location and the removal and

replacement procedure. This ends the procedure.

No:

Continue with the next step.

2. Locate the NVMe Flash adapter by using the PCI address:

a) The operating system log contains information about the NVMe Flash adapter in the form of a PCI

address. Record the PCI address information for the NVMe Flash adapter that has failed. For

example, in the operating system log message

nvme 0006:01:00.0: Failed status:

ffffffff, reset controller

, the PCI address of the failing NVMe Flash adapter is

0006:01:00.0.

b) At the command line, type

lscfg -vl pciaddress

, where

pciaddress

is the NVMe Flash

adapter information that you recorded in step 2.a. Then, press Enter.

c) Record the slot number information that is in the location code field.

d) Replace the adapter. Go to “5104-22C or 9006-22C locations” on page 63, “9006-12P locations”

on page 75 , or “9006-22P locations” on page 91 and use the slot number information to identify

the physical location and the removal and replacement procedure. This ends the procedure.

Identifying the location of the storage device

Use this procedure to identify the location of a storage device.

About this task
The storage device location is determined in the drive removal and replacement procedures for your

system. See Removing a disk drive from the 5104-22C or 9006-22C system, Removing and replacing a

storage drive in the 9006-12P, or Removing and replacing a disk driv e in the 9006-22P.

User guides for PCIe adapters

Use this information to find the user guide for your PCIe adapter.

About this task

Use the following table to find the user guide for the PCIe adapter that you are using.

Table 7. PCIe adapter user guides
Name

User guide

Broadcom

Broadcom website (http://www.broadcom.com)

Beginning troubleshooting and problem analysis 17

Содержание Power Systems Series







































































































































Результаты поиска

Содержание Power Systems Series

Отзывы:

Похожие инструкции для Power Systems Series

Бренды по названию

Популярные бренды

IBM Power Systems Series, Анализ проблем, составные части системы и расположение

Результаты поиска

Содержание Power Systems Series

Отзывы:

Похожие инструкции для Power Systems Series

Бренды по названию

Популярные бренды