manualshive.com logo in svg

IBA BM-PN, Руководство пользователя, Страница: 67 / 77

Поделиться
Скачать
IBA BM-PN Скачать руководство пользователя страница 67

ibaBM-PN 

Manual 

 

 

 

Issue 1.9 

67 

 

11 

Technical data  

11.1  Main data  

Manufacturer  

iba AG, Germany 

Order no.  

13.120000

 

Description  

PROFINET bus monitor  

PROFINET interfaces  

Number 

3 (2 x PROFINET devices for up to 2 PROFINET lines,  

1 x sniffer) 

PROFINET devices  

2 x 2-port switches  

Each with 2 x RJ45 socket 10/100 Mbit/s, autonegotiation 
With the autonegotiation switched off, the port P2R of each 

device works as uplink port  

TAP interface (sniffer) 

2-port switch, 2 x RJ45 socket, 10/100 Mbit/s 

Functions 

2 x PROFINET device, shared device (up to 4 controllers each), 

RT, IRT (≥ 250 μs), 

MRP and MRPD Client, NetLoad Class III, 

S2 system redundancy 

ibaNet interface  

Number 

1 (e. g. for the connection to ibaPDA) 

Design 

Fiber optic cable 

ibaNet protocol  

32Mbit Flex (bidirectional) 
Up to 15 devices can be connected in a FO ring topology 
Can be used for data, settings and service purposes (e.g. 

updates) 
max. 1024 analog signals (BYTE, INT, WORD, DINT, DWORD, 

FLOAT, Big/Little Endian) + max. 1024 digital signals (BOOL) 
max. 4060 bytes at a cycle time of 1.4 ms 

Data transmission rate 

32 Mbit/s 

Sampling time 

From 125 µs, freely adjustable 

Connector type 

2 ST connectors for RX and TX 

The use of fiber optic cables of type 62.5 μm/125 μm is 

recommended. For information on cable length, see chap. 11.4. 

Transmitting interface (TX) 

 

Output power  50/125 µm FO cable 

-19,8 dBm to -12,8 dBm 

  62,5/125 µm FO cable 

-16 dBm to -9 dBm 

  100/140 µm FO cable 

-12,5 dBm to -5,5 dBm 

  200 µm FO cable 

-8,5 dBm to -1,5 dBm 

Temperature range  -40 °F to 185 °F (-40 °C to 85 °C) 

Light wavelength  850 nm 

Receiving interface (RX) 

 

Sensitivity

2

  62,5/125 µm LWL-Faser: 

-30 dBm 

Temperature  77 °F (25 °C) 

                                                      

2

 Data for other FO cable diameters not specified 

Содержание BM-PN














































































Отзывы:

Нет отзывов