IBA BM-PN Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 77

IBA BM-PN Скачать руководство пользователя страница 59

ibaBM-PN

Manual

Issue 1.9

59

9.3

Configuring outputs

Outputs can be used to send signals from ibaPDA to a PROFINET controller via a device

slot.
The device must have at least one slot with input data for this purpose. This must be

taken into account in the controller configuration.
For configuring the outputs, select the "Outputs" tab in the I/O Manager. Modules which

have been configured on the input side (hardware tab) may be displayed here.

Figure 42: “Outputs” tab in I/O Manager

Note

ibaPDA processes output signals with lower priority compared to the acquisition of input

signals with a cycle not faster than 50 ms depending on the I/O configuration.

9.3.1

Device module “ibaBM-PN”

For a description of the settings, see the "General" tab, chapter 9.2.1.1.
When selecting the "Outputs" menu, modules already configured under "Hardware" may

be displayed. Signals can only be output with modules of the type "Device slot".
You can configure a new module of the "Device slot" type by clicking on the blue "Click

to add module…" command. Add the module by clicking on <OK>.

9.3.2

"Device slot" module

The settings on the "General" tab are described in chapter 9.2.3.

Output of analog values

Define the analog values you want to output in the "Analog" tab.



Name

Here, you can enter a signal name and additional two comments when clicking the

symbol in the signal name field.

«
...
57
58
59
60
61
...
»

Содержание BM-PN














































































Отзывы:

Нет отзывов