manualshive.com logo in svg

IBA BM-PN, Руководство пользователя, Страница: 20 / 77

Поделиться
Скачать
IBA BM-PN Скачать руководство пользователя страница 20

 

Manual 

ibaBM-PN 

 

20 

Issue 1.9 

 

 

8.6 

Data acquisition in mixed operation 

 

Figure  8:   Data acquisition with 2 devices and TAP/Sniffer 

With the example above, we show one possible scenario how to combine the different 

versions. 
Here, we show the data acquisition via TAP/Sniffer and both PROFINET devices. 
The installation location within the PROFINET line is relevant regarding the TAP inter-

face. The TAP interface always has to be integrated linearly. You can only acquire data 

which are transmitted at this position in the network. 

8.7 

Data acquisition at SINAMICS Link 

SINAMICS Link  is a special type of PROFINET communication for exchanging 

PROFINET IRT data between Siemens SINAMICS controllers. SINAMICS Link is based 

on a strict, straight network topology with a maximum of 64 PROFINET (PN) controllers. 
 

 

Note 

SINAMICS Link allows data exchange between the Control Units CU320-2PN and 

CU320-2DP. For this purpose they must be equipped with the CBE20 option board. 

 

8.7.1 

2 or more SINAMICS Link participants 

 

Figure  9:   Data acquisition as Sniffer at SINAMICS Link 

The point of installation within the SINAMICS Link is not relevant. The TAP interface 

always has to be integrated linearly.  

Содержание BM-PN














































































Отзывы:

Нет отзывов