manualshive.com logo in svg

IBA BM-PN, Руководство пользователя, Страница: 64 / 77

Поделиться
Скачать
IBA BM-PN Скачать руководство пользователя страница 64

 

Manual 

ibaBM-PN 

 

64 

Issue 1.9 

 

 

10 

PROFINET engineering  

 

 

 

Connecting and removing PROFINET cables  

Changes in the PROFINET network might have an impact on the functionality of the 

control system. 

 

 

10.1  Operation as device  

For operating as device, you have to configure it in the engineering tool of the used 

PROFINET controller. 
You have to carry out the following basic steps:  

1. 

Install the GSDML file. The ibaBM-PN will be integrated in the hardware catalog in 

PROFINET IO -> General -> iba AG -> iba BM -> ibaBM-PN busmonitor. 

2. 

Insert the ibaBM-PN device in the configuration of the PROFINET controller. 

3. 

Assign at least one module to a slot of the device. 

4. 

Adapt the PROFINET network configuration, if required (e.g. sending clock cycle, 

synchronization…). 

5. 

Assign the configured device name. 

 
You find the GDSML file on the “iba Software & Manuals“ DVD under 
\02_iba_Hardware\ibaBM-PN\01_GSD_File\ 

Substitute values 

During connection loss to the PN controller 0 will be used as substitue value for analog 

and digital values. 

Maximum amount of process data 

The maximum amount of process data is determined by the maximum telegram size (net 

1440 bytes of IOCR data) and the number of subslots with input or output data (param-

eters in the GSD file).  
The maximum data length in bytes is:  

  Max. number of input bytes = MaxInputLength - 4 - (number of input-subslots) – 

(number of output-subslots) 

  Max. number of output bytes = MaxOutputLength - 4 - (number of input subslots) – 

(number of output-subslots) 

A submodule containing both input and output data must be counted as input subslot 

and as output subslot. 

 

 
 

Содержание BM-PN














































































Отзывы:

Нет отзывов