manualshive.com logo in svg

IBA BM-PN, Руководство пользователя, Страница: 36 / 77

Поделиться
Скачать
IBA BM-PN Скачать руководство пользователя страница 36

 

Manual 

ibaBM-PN 

 

36 

Issue 1.9 

 

 

 

Application Relation

 

Each PN controller can be connected to one or more slots, but each slot is as-

signed to only one PN controller. The „Application relation“ column shows the index 

and the IP address of the connected PN controller for that slot.  

If the PROFINET device is operated as S2 device, the index and IP addresses of 

both PN controllers are displayed in the column. 

 

Output/Input

  

A slot can consist of output and input bytes. 

 

Length

 

Size of the data bytes 

 

State

 

The state is indicated by a description and a color:  

  Green: a controller is connected and the slot state is GOOD 

  Orange: a controller is connected and the slot state is BAD, e.g. the controller is 

in STOP. 

  Red: no controller is connected 

 

Cycle time

 

Cycle duration 

 

9.2.3 

“Device slot“ module 

The module „device slot“ is only available underneath a device node. 

9.2.3.1  “General“ tab  

 

Figure 19: “Device slot“ module – “General“ tab 

Basic settings 

 

Module type, Locked, Enabled, Name, Timebase, Use name as prefix 

see chapter 9.2.1.1.

 

 

Module No. 

Logical module no. for clearly referencing of signals, e.g. in expressions in virtual 

modules and ibaAnalyzer. 

Содержание BM-PN














































































Отзывы:

Нет отзывов