manualshive.com logo in svg

IBA BM-PN, Руководство пользователя, Страница: 21 / 77

Поделиться
Скачать
IBA BM-PN Скачать руководство пользователя страница 21

ibaBM-PN 

Manual 

 

 

 

Issue 1.9 

21 

 

In this configuration, ibaBM-PN can be integrated into the SINAMICS Link at any point 

between two control units and read data. 

8.7.2 

1 SINAMICS Link participant 

 

Figure  10:   Data acquisition as Sniffer at SINAMICS Link with only one participant 

To enable data acquisition at the SINAMICS Link with only one controller, one of the two 

PROFINET devices can be switched to the SINAMICS emulation mode. The device can 

then no longer be used as a normal PROFINET device. 
Port 1 (P1R) of the respective PROFINET device and one of the two ports of the TAP 

interface are connected with a patch cable. The second port of the TAP interface is con-

nected to the controller. 
The actual data acquisition is realized via a “Sniffer SiLink” module, as when operating 

with several SINAMICS controllers. 
 

8.8 

Data acquisition on redundant PROFINET 

 

Figure  11:   Data acquisition on redundant PROFINET 

PROFINET system redundancy is distinguished into three configurations with the desig-

nations S2, R1 and R2. ibaBM-PN only supports "S2" configurations. 
Each of the two PROFINET devices of the ibaBM-PN supports S2 redundancy sepa-

rately, i.e. configurations with the use of one or two PROFINET devices (analog to chap-

ter 8.1 and 8.2) are possible. 

Содержание BM-PN














































































Отзывы:

Нет отзывов