Hydronix Hydro-Control VI Скачать руководство пользователя страница 89

Страница: 89 / 104

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

Chapter 8

Backup, Restore and Upgrade

1 The System and Data Cards and USB memory stick

The Hydro-Control incorporates a System Card and a Data Card. These cards are accessed via

the top access plate. The identification, removal and replacement of these cards is described in

Chapter 2.

1.1

The System Card (Hydronix Replacement Part Number 0176)

The System Card holds the main operating files of the Hydro-Control. This is specific to the

type of unit and should not be changed between units. (Not applicable to HC06 v2)

1.2

The Data Card (Hydronix Replacement Part Number 0177)

The Data Card holds the mix log database and system settings. With the power supply off, this

can be removed and replaced if necessary. (Not applicable to HC06 v2)

1.3

USB Memory Stick

Figure 52: The Hydro-Control VI side view showing the USB ports

There are three USB ports sited on the left hand side when looking at the front of the unit. A

Memory Stick may be used for backing up and restoring recipes, system parameters and mix

log files.

If the Hydro-Control USB ports are difficult to access then a USB extension with a panel

mounted socket is available from Hydronix – Part Number 0175.

The Memory Stick may be inserted and removed with the power supply on. Do not remove the

Memory Stick when a backup or restore is in progress.

The USB ports

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды