Hydronix Hydro-Control VI Скачать руководство пользователя страница 18

Страница: 18 / 104

Mechanical Installation

Chapter 2

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

HC06 v1

HC06 v2

Figure 5: View of the Hydro-Control VI showing the mounting brackets

2 Mounting and installation

The unit should be mounted in a control panel (maximum thickness 8mm) using a bracket on each

side, two brackets on the top and two brackets on the bottom. To fit the side brackets, locate the

bracket in the slots on the side of the unit and slide it down until the top and bottom of the bracket

are level with the case. To fit the top and bottom brackets, insert the bracket into the slot and

tighten the bolt.

To install the Hydro-Control

•

Cut out an aperture in the panel of the correct size. See Figure 6 for a template.

•

Remove the mounting brackets from the body of the unit by releasing the screws and then

unhooking the brackets.

•

Insert the Hydro-Control through the prepared hole.

•

Re-fit the mounting brackets to the unit and tighten the screws evenly to pull the fascia

towards the control panel.

Panel or Enclosure

Cut-out for

Hydro-Control

232mm (9.14")

178mm (7.01")

Figure 6: The panel cut-out for the Hydro-Control VI

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды