manualshive.com logo in svg

Hydronix Hydro-Control VI, Руководство по установке

Поделиться
Скачать
Hydronix Hydro-Control VI Скачать руководство пользователя страница 19

Chapter 2 

Mechanical Installation 

 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

19 

3  Operating Temperature 

The unit has been designed to work in ambient air temperatures inside the cabinet of 0 – 40 °C 

(32 – 104 °F). 

Where ambient temperatures vary from this a temperature regulation system may need to be 

installed. 

4  OPTO modules 

The OPTO-22 I/O modules are accessed through the removable panel on the rear of the unit.  The 

panel is held in place by four captive screws.  When the screws are released and the panel is 

removed,  the OPTO modules can be individually removed and replaced using their individual 

retaining screws.  All power should be removed, from both the unit and the field wiring, whilst the 

cover is not in place. 

5  Memory Cards 

Note: HC06 v2 utilises an internal SSD hard drive and does  not contain removable 

memory cards  (Figure  5). The SSD hard drive is not removable,  therefore,  no user 

maintenance is possible. Contact [email protected] for assistance in the event of 

a failure.    

There are two memory card slots and these are accessed by removing the mounting bracket on 

the top left corner of the Hydro-Control (as viewed from the rear).  Removing the two small screws 

opens the access plate over the card sockets (shown in Figure 7). 

 

Figure 7: The memory card access port showing the labels of the cards 

As shown in Figure 7, the memory cards are mounted so that the System Card is nearest to the 

front of the unit and the Data Card is nearest to the rear.  Both cards are clearly labelled.  The 

System Card is coloured blue and the data card is coloured beige. 

The memory cards should always be inserted so that the Hydronix Logo is facing the rear of the 

unit.  The System Card should never be transferred between units. 

If needed the System Card can be replaced with Hydronix Part Number 0176.  The Card must be 

replaced with the same colour card as the original factory fitted card. 

Over time the memory cards can degrade in performance and so the Data Card should be replaced 

every five years with Hydronix Part Number 0177. 

Use Hydronix original parts to ensure compatibility and continuing reliability of the unit. 

Memory 

Cards 

Содержание Hydro-Control VI









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды