Hydronix Hydro-Control VI Скачать руководство пользователя страница 64

Страница: 64 / 104

System Design

Chapter 5

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

4.3

Admix control

The effect that an admixture has on the sensor signal will depend on the admixture itself and

the point at which it is added to the mixer. The Hydro-Control has an output for controlling the

addition of the admixture that may be configured using the Admix Signal parameter on the

second page of the System Parameters.

Moisture

Time

START

Pre-wet

Water

Added

Dry Mix Time

Main Water

Addition

Wet Mix

Time

MIX COMPLETE

Add

Cement

Admix Output

Water

Admix

All

Admix Enable %

Admix Type Set to:

Point set by the ‘Admix Enable’

parameter in the recipe

Figure 44: The Admix output signal during a normal mix cycle

When the Admix Signal parameter is set ‘Admix Enable %’ the Admix output is set high during

the Main Water addition when the percentage of the main water dosed reaches the recipe

parameter ‘Admix Enable’. The total water used to calculate the percentage is the calculated

amount (in CALC Mode) or the amount dosed in the previous batch (in AUTO Mode).

This is used to delay the admixture addition until a set amount of water has been dosed. This

can be a requirement given by the manufacturer of the admixture.

When the Admix Signal parameter is set to ‘Water’ the Admix output is set high whenever the

water is being added to the mixer.

When the Admix Signal parameter is set to ‘Admix’ the Admix output is set high during the main

water addition phases of the mix cycle. This is to provide backwards compatibility with the

Hydro-Control V.

When the admix signal is set to ‘All’ the Admix output is set high from the time the Hydro-Control

receives the Start signal until the time that the Hydro-Control outputs the Mix Complete signal.

This is equivalent to the busy output on the Hydro-Control V.

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды