Hydronix Hydro-Control VI Скачать руководство пользователя страница 65

Страница: 65 / 104

Chapter 5

System Design

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

Moisture

Time

START

Pre-wet

Water

Added

1st

Dry Mix

Time

Main

Water

Addition 1

Wet Mix

Time

MIX COMPLETE

Add

Cement

Admix Output

Admix Type Set to:

Water

Admix

All

Admix Enable %

Point set by the “Admix Enable”

parameter in the recipe

2nd

Dry Mix

Time

Main

Water

Addition 2

Figure 45: The Admix output signal during a 2-step mix cycle

If the recipe is configured to 2-step addition mode then, when the Main Water addition is added

using Preset Mode, the mix cycle will add the Main Water to the mixer in two portions, defined

by the Admix Enable parameter in the recipe. After Main Water Addition 1, the Dry Mix phase

will be run a second time.

At the end of each of the Dry Mix phases, the system will obtain an average reading of the

sensor value as defined by the ‘Averaging Time’ parameter in the System Parameters.

If this 2 step batch is used to calibrate a recipe, then a second gain and offset value will be

calculated for the recipe and this will be used to calculate the moisture whenever the unscaled

value rises above the average unscaled vale from the second Dry Mix phase. This will happen

in either AUTO or CALC Modes.

This functionality is useful if an admixture is being used which makes a large change to the

calibration of the material in the mixer. The 2 step addition mode will rescale the moisture

display on the graph on the main screen so that it is more representative of the moisture in the

mixer.

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды